Update June 5, 2024
We now have fixes for CVE-2024-24919 for releases dating back to R77.30 with latest JHF.
Update June 4, 2024
The procedure to identify vulnerable Security Gateways in sk182336 - Hotfix for CVE-2024-24919 was updated.
The Gateways script was replaced with v3. The updated script checks if the Hotfix is installed.
Update June 03, 2024
Automatic interim preventative measure deployed through AutoUpdater utility
Security Gateways that were configured to the Check Point's Auto Update process are gradually receiving an update (as of June 2, 2024), which helps protect them from various attempts to exploit the CVE. This is an interim preventative measure until the Hotfix is fully installed on customers’ Security Gateways. It is important to emphasize that installing the Hotfix in sk182336 is the best way to stay protected from this vulnerability.
This is relevant for gateways running R80.40 and above. Instructions to confirm this is enabled are in sk182336.
Update June 01, 2024
Quantum Spark
We now have a specific SK related to CVE-2024-24919 for Quantum Spark appliances! : sk182357
In addition to providing links to updated firmware, this SK lists the specific remediation steps that may be necessary on Quantum Spark Appliances, which includes:
- Disable the Remote Access VPN blade
- Change the Administrator passwords and use complex passwords
- Restrict access through "Reach My Device"
- Enable Two-Factor Authentication for Administrators (R81.10.10 and higher)
- Enable Two-Factor Authentication for Remote Access VPN users (R81.10.10 and higher)
- Enable notifications for administrator access
cccd
In R81.10 we added a feature to improve VPN performance - named CCCD
This feature is disabled by default, and we know about few advanced customers who are using it.
Customers who enable CCCD are still vulnerable to CVE-2024-24919 even after installing the Hotfix!
YOU MUST DISABLE CCCD TO BECOME PROTECTED!
Instructions below and also on SK182336:
Run the command: vpn cccd status
The expected output is: vpn: 'cccd' is disabled.
If the output differs, stop the CCCD process by running the vpn cccd disable command.
Updated May 31, 2024
To streamline information flow and simplify actions for our customers and partners, we have consolidated all relevant details about CVE-2024-24919 and its remediation into a single SecureKnowledge article: sk182336.
Please revisit it now, as we have added some updates.
Updated May 30, 2024
To remain protected from CVE-2024-24919, it is mandatory install this on Check Point Quantum and Spark gateways following fix.
In addition, you should take the following extra security measures, which are documented in sk182336:
- Change the password of the LDAP Account Unit
- Reset password of local accounts connecting to Remote Access VPN with password-only authentication
- Prevent Local Accounts from connecting to VPN with Password-Only Authentication
- Renew the server certificates for the Inbound HTTPS Inspection on the Security Gateway
- Renew the certificate for the Outbound HTTPS Inspection on the Security Gateway
- Reset Gaia OS passwords for all local users
- Regenerate the SSH local user certificate on the Security Gateway (see the SK for more details)
- Renew the certificate for the SSH Inspection
Update May 28, 2024
Yesterday (May 27th) we delivered a solution that addresses attacks we saw on a small number of customers’ VPN remote access networks.
Today we found the root cause for these attacks and are now releasing a fix. To remain protected, it is mandatory install this on Check Point Quantum and Spark gateways following fix.
The vulnerability we found (CVE-2024-24919) affects Security Gateways with remote access VPN or mobile access blade enabled. It is potentially allowing an attacker to read certain information on Gateways once connected to the internet and enabled with remote access VPN or mobile access.
The fix we developed prevents the use of this vulnerability, once deployed on the relevant Gateways. Install this now to stay protected.
The attempts we’ve seen so far, inline with what we alerted you yesterday, are focusing on remote access on old local accounts with unrecommended password-only authentication within the known small customers we referred to yesterday. Check Point’s network is not affected by this.
More information on today’s notification can be found here.
Customer security is our top priority. We will continue to investigate this issue and provide additional updates.
For additional information, please contact Check Point Support Center or your Check Point representative.
Originally posted on May 27, 2024.
Over the past few months, we have observed increased interest of malicious groups in leveraging remote-access VPN environments as an entry point and attack vector into enterprises.
Attackers are motivated to gain access to organizations over remote-access setups so they can try to discover relevant enterprise assets and users, seeking for vulnerabilities in order to gain persistence on key enterprise assets.
We have recently witnessed compromised VPN solutions, including various cyber security vendors. In light of these events, we have been monitoring attempts to gain unauthorized access to VPNs of Check Point’s customers.
By May 24, 2024 we identified a small number of login attempts using old VPN local-accounts relying on unrecommended password-only authentication method.
We have assembled special teams of Incident Response, Research, Technical Services and Products professionals which thoroughly explored those and any other potential related attempts. Relying on these customers notifications and Check Point’s analysis, the teams found within 24 hours a few potential customers which were subject to similar attempts.
Password-only authentication is considered an unfavourable method to ensure the highest levels of security, and we recommend not to rely on this when logging-in to network infrastructure.
Check Point has released a solution, as a preventative measure to address these unauthorised remote access attempts.
We encourage our customers to enhance their VPN security posture by:
- Check if you have local accounts, if they were used and by whom.
- If you don’t use them – best to disable them.
- If you have local accounts which you want to use and are password-only authenticated, add another layer of authentication (like certificates) to increase your environments IT security.
- As said, If you are a Check Point customer, deploy our solution on your Security Gateways. This will automatically prevent unauthorized access to your VPNs by local accounts with password-only authentication method.
Learn more and receive practical guidance for configuration monitoring and practices to enhance your VPN security posture.
For any additional assistance required, please contact Check Point technical support Center or your local Check Point representative.
We value the collaboration of our customers and dedication of our teams to reach a solution which effectively addresses any such attempts.
