- Products
- Learn
- Local User Groups
- Partners
- More
Firewall Uptime, Reimagined
How AIOps Simplifies Operations and Prevents Outages
Introduction to Lakera:
Securing the AI Frontier!
Check Point Named Leader
2025 Gartner® Magic Quadrant™ for Hybrid Mesh Firewall
HTTPS Inspection
Help us to understand your needs better
CheckMates Go:
SharePoint CVEs and More!
HI All,
I have made a setup for a cluster of 5600 series devices with Gateway and management. have some policies installed. While doing the clean image installation and hotflix, I am not able to peer or sync my FW01 to FW02.
1) I have made my FW01 as active before doing the clean image on FW02.
2) Install the R81.10_T335 and Check_Point_R81_10_JUMBO_HF_MAIN_Bundle_T150_FULL.
3) Make my FW02 a secondary while running the wizard. also given IP the same as given before.
4) After clean image installation is complete, I am able to sync with my FW01, but after clean image installation of my FW01, I am not able to sync with my FW02. Also, it is asking to run the new cluster wizard.
What options were selected during First Time Wizard when fresh installing FW02?
What specific errors are shown when you try to sync?
sory for delay response, error when doing clean image on FW01 and connecting to smart console, it's asking to create new cluster. when we connect to FW02 smart console then there will be no option to sync FW01 due to SIC
Hi @VIKASH_GIRI
Do you van to create a new cluster, or you have a cluster object, and you want to sync the newly installed member into this object?
If you want to SIC the newly installed member into an existing cluster object, you need to reinitiate teh SIC.
Do you want to do this, or I misunderstood something?
Akos
I want same cluster and sync with new clean image FW01 and FW02, also when i am doing the clean image on my FW01 (primary cluster) my all policy getting erase.
i can't reinitiate the SIC to my FW01 bcz it done have SIC. (while running wizard i am selecting FW01 as primary on cluster) 
snap attached
Hi @VIKASH_GIRI
First clarify the setup, before I give wrong advise.
First, and most important to clarify this.
Akos
3) You want to arrange them into one new cluster. Yes
hi @VIKASH_GIRI
Now the setup is clear.
Have you read this guide?
Akos
Thanks, I will go through the guide. also, i don't want to lose my connectivity while performing this activity.
But you wrote that, you don't have enough free space to install a hotfix. What consumes a lof of space on a disk?
Did you try to find the files, directories?
Akos
Nop, setup running on client place and i am testing this on my lab.
Hi @VIKASH_GIRI
I thought that it is a live environment. 🙂 In this case, I wish you a good testing.
Bear in mind, the fullHA setup seems to be a good thing for the first sight, but is had only bad experiences with that.
I prefer the distributed setup to Full-HA. Much more easier, and failureproof
Akos
You can't sync a freshly installed primary management instance back from an existing secondary one, the product doesn't work that way. The primary instance is the CA for all the SIC, it's the one that manages all the certs for the communication. If there's no primary then there's no SIC.
You can look to promote your secondary to become the primary, then rebuild FW01 to be the new secondary.
thnks for update, i tried all way but not able to complete, i think we need to make on standby device and take backup for old device.
You should probably fresh install the new kit and follow the Advanced Migration steps in the Install guide linked earlier in this thread.
Keep in mind, as LOTS of people always confuse these things. You canNOT promote secondary to be primary or demote primary into secondary. Primary mgmt will ALWAYS be primary and SECONDARY will ALWAYS be secondary, UNLESS rebuilt. Standby can become active and active can be set as backup.
Anyway, please send send commands @AkosBakos mentioned:
cphaprob state
cphaprob -a if
cphaprob -i list
cphaprob -l list
cphaprob syncstat
cpstat mg
Andy
Though, seems you could do this to promote secondary to primary:
To promote a Secondary server to become the Primary server:
#$FWDIR/bin/promote_util
#cpstop
$FWDIR/conf/mgha*
files. They contain information about the current Secondary settings. These files will be recreated when you start the Check Point services.mgmtha
license on the newly promoted server.
Note - All licenses must have the IP address of the promoted Security Management Server.
cpstart
on the promoted server.Note - When you remove the old Primary server, all previous licenses are revoked.
My primary mgmt lab (does NOT matter if its active or standby)
[Expert@CP-MANAGEMENT:0]# grep Primary $CPDIR//registry/HKLM_registry.data
:Primary ("[4]1")
[Expert@CP-MANAGEMENT:0]#
secondary:
[Expert@CP-MANAGEMENT-HA:0]# grep Primary $CPDIR//registry/HKLM_registry.data
:Primary ("[4]0")
[Expert@CP-MANAGEMENT-HA:0]#
This is a duplicate ! Can you delete this one ?
Ho @VIKASH_GIRI
What do the following commands say?
cphaprob stat
cphaprob -a if
The SIC is Ok between the GW-s and MGMT?
Ákos
Leaderboard
Epsum factorial non deposit quid pro quo hic escorol.
User | Count |
---|---|
16 | |
11 | |
7 | |
6 | |
6 | |
5 | |
4 | |
4 | |
4 | |
3 |
Tue 07 Oct 2025 @ 10:00 AM (CEST)
Cloud Architect Series: AI-Powered API Security with CloudGuard WAFThu 09 Oct 2025 @ 10:00 AM (CEST)
CheckMates Live BeLux: Discover How to Stop Data Leaks in GenAI Tools: Live Demo You Can’t Miss!Thu 09 Oct 2025 @ 10:00 AM (CEST)
CheckMates Live BeLux: Discover How to Stop Data Leaks in GenAI Tools: Live Demo You Can’t Miss!Wed 22 Oct 2025 @ 11:00 AM (EDT)
Firewall Uptime, Reimagined: How AIOps Simplifies Operations and Prevents OutagesAbout CheckMates
Learn Check Point
Advanced Learning
YOU DESERVE THE BEST SECURITY