Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
Gombodorj
Explorer

Maestro cluster member "down" after VSX command

Hello, I have one MHO-140, one SMS, two 6700 appliances working in VSX mode in one SG. 

I was trying to configure bond interface and I used "set vsx off". Right after that member #2 has gone "down" in cphaprob state. I can ping/ssh to 192.0.2.2 from 192.0.2.1.

Click to Expand

[Expert@mn-dc1-r1c1-sec-fw.vsx1-ch01-02:0]# cphaprob state

Cluster Mode: HA Over LS

ID Unique Address Assigned Load State Name


1 192.0.2.1                       100% ACTIVE(!) mn-dc1-r1c1-sec-fw.vsx1-ch01-01
2 (local) 192.0.2.2               0% DOWN mn-dc1-r1c1-sec-fw.vsx1-ch01-02


Active PNOTEs: VSX, pull_config

Last member state change event:
Event Code: CLUS-112000
State change: INIT -> DOWN
Reason for state change: USER DEFINED PNOTE
Event time: Mon Nov 28 09:32:42 2022

[Expert@mn-dc1-r1c1-sec-fw.vsx1-ch01-02:0]#

I didn't anything other than "set vsx on/off". What could be the issue?

 

0 Kudos
9 Replies
_Val_
Admin
Admin

It says "USER DEFINED PNOTE". Any chance you used admin down on one of the shoulders?

0 Kudos
Gombodorj
Explorer

No, I didn't use admin down command. In fact, I tried to use admin up command it didnt work as well.

0 Kudos
_Val_
Admin
Admin

Please post output of "cphaprob -l list" command here from the faulty member

 

0 Kudos
Daniel_Szydelko
Advisor
Advisor

Hello,

In addition you can paste the output from some extra cmds - just to show overall state:

g_all cpinfo -y all

vsx stat -v
vsx stat -l

vs_all g_all asg stat vs

asg stat vs all

BR

Daniel.

0 Kudos
Gombodorj
Explorer

Hi, I put the output of those commands in one file. Thanks for help

0 Kudos
_Val_
Admin
Admin

Hi, this is what I see:

Device Name: VSX
Registration number: 3
Timeout: none
Current state: problem
Time since last report: 0.2 sec
Problematic VSIDs: 1.

Device Name: pull_config
Registration number: 14
Timeout: none
Current state: problem
Time since last report: 56.4 sec

 One of the VSs reports a problem and cannot pull config scripts. 


Try opening that VS object in the management for editing and press OK. This should initiate a config push to the VS. Finally,  If it does not help, please open a TAC request.

Also, did you run "vsx mode on" on that cluster member after configuring the bond? Also, you are supposed to configure bonds from MHO, why would you touch an appliance?

 

0 Kudos
Gombodorj
Explorer

I was trying to bond Eth1-5, eth1-6 uplink ports to a switch. On the MHO there are no uplink ports, it only shows downlink ports.

0 Kudos
emmap
Employee
Employee

Bonds are configured at the security group, not the MHO.

I'm not aware of setting vsx off causing a pnote (were in in global mode when you ran that?) but if it did, it should resolve after setting it back on again. Worst case you may need to reboot the SGM.

0 Kudos
Daniel_Szydelko
Advisor
Advisor

You can try from SGM 1_2:

vsenv 0

cpha_blade_config pull_config all 192.0.2.1

vsenv 1

cpha_blade_config pull_config all 192.0.2.1

then reboot SGM 1_2 and check it again.

 

Anyway I think it isn't proper order to configure Maestro VSX SG.

BR

Daniel.

0 Kudos