Easy Tool - Real time connection table analysis v4...

HeikoAnkenbrand

Overview

From version R80.10 to version R81.10.

For many Check Point users the question arises again and again, which connections and services are used by a rule, a port, an destination IP or source IP in real time. For this purpose I have created a small tool, which all information about a rule can be read out in real time from the connection table.

This is good for optimizing the ruleset, as it provides a real-time view of the connection table with the corresponding info. This can be a good solution in more complex environments to see what this rule really do.

The following questions can be answered:

In which rules is port 443 currently used?
In which rules is the source or destination IP is used?
Which connections, ports, protocols and are active for rule xy?
How many connections are there for rule xy in the TCP SYN, ACK or FIN state?
How can I simplify rules and combine them, for example, into class C or B networks?
What IP communication is there e.g. for port 80 or for the rule xy?

This tool will help you quickly answer these questions and many more.

Tool

When you execute this oneliner, a new cli command "econn" will be created.
After that, you only need to execute the following cli command in expert mode with the parameters.

The output of the tool always show:

Shows all rules to which the filter applies
Shows all UDP and TCP ports to which the filter applies.
Shows a summary of all TCP (SYN, Syn-ACK, ACK,FIN) , UDP, ICMP, VRRP, IGMP values for the filtered connections.
Indicates which protocols are currently in use (TCP, UDP,...)
Summary of all used Check Point services (https, echo-request, CPD_amon, FW1_log,...)
Incoming and outgoing interface (eth0, bond1.10, ...)
Check Point service names
Formatted output of the connection table:
(rule, protoll ,source IP, source port, destination IP, destination port, session timeout, TCP state, interface in and out, Check Point service)

Since version 3.0 VSX is supported:
On VSX systems, change to the corresponding virtual system with "vsenv" and execute "econn" on that VS system.

Filter Syntax	Description
-a	Show the information about the complete connection table.
-r <rule number>	Show the information about a specific rule with the corresponding rule number. Inline rules for example 2.1 are not possible. You can only use the base rule in this case 2.
-p <port>	Show the information about a specific destination port with the corresponding port number.
-d <destination IP>	Show the information about a specific destination IP with the corresponding IP.
-s <source IP>	Show the information about a specific source IP with the corresponding IP.
-g <grep parameter>	Search filter for the corresponding grep parameters in the raw data of "fw ctl conntab".
-e <grep parameter>	Search filter for the corresponding grep parameters in the connection table output view.

Delete Connections	Description
-x	Attention!!! This parameter deletes all connections from the connection table that match the filters. Grep parameters (-g) cannot be deleted in the combination with this option. This parameter is only available from R81 and higher.

Output extension	Description
-c	Shows the corresponding connection table entries.
-t	Tip! Display possible class C and B networks where the corresponding IP addresses from the connection table would match. This function is good to simplify rules.
-i	Displays only the summarized IP communication. Also used to simplify the set of rules.
-n	No summary output.

File

Description

-w <file name>

Write connection table to file.

-f <file name>

Read connection table from file.

Important!
Search filters (-r, -p, -d, -s ) only work when writing the file -w not with the option -f.

Examples

Examples	Description
# econn -r 10 -c	Shows all basic informations (used Ports, counter TCP/UDP/ICMP...) to rule 10 and displays the appropriate connection table entries.
# econn -a	Gives an overview of all connectiontabel entries (used ports, used protocols and counter TCP/UDP/ICMP...).
# econn -p 443 -c	Displays all rules where port 443 is used and prints all connection table entries.
# econn -d 1.1.1.1 -c	Displays all rules where destination IP 1.1.1.1 is used and gives an overview of all connection table entries (used ports, used protocols and counter TCP/UDP/ICMP...) and prints all connection table entries.
# econn -s 1.1.1.1 -c	Displays all rules where source IP 1.1.1.1 is used and gives an overview of all connection table entries (used ports, used protocols and counter TCP/UDP/ICMP...) and prints all connection table entries.
# econn -s 1.1.1.0-1.1.1.255	Displays all rules where source IP range from 1.1.1.1 to 1.1.1.255
# econn -r 10 -t -i	Shows all basic informations to rule 10 and summarizes all IP addresses to possible class C and B networks and output the IP communication summed by source IP's.
# econn -p 80 -t -i -c	Shows all possible informations to port 80 in the connection table: rules, connection summaries, used protocols and ports, grouped networks, IP communication
# econn -p 443 -g SYN -c	Shows all possible informations to port 443 in the connection table with "TCP SYN" state
# econn -r 10 -p 53 -x	Attention!!! Delete all possible connections with port 53 in rule 10 in the connection table.
# econn -w test -p 433	Write the connection table to tar file where port 443 is used.
# econn -f test -c -e SYN	Read the connection table from tar file and show the output with the filter view option for SYN.
# econn -n -p 443 -e SYN_SENT	Don't show the connection summary + show connection table for port 443 and TCP state SYN.

Install Tool

Use this auto installer script from "Spoiler" on the Firewall Gateway as CLI command in expert mode:

Click to Expand

curl_cli -k http://www.ankenbrand24.de/inst_econn > /tmp/inst_econn && chmod 770 /tmp/inst_econn && /tmp/inst_econn

curl_cli -k http://www.ankenbrand24.de/inst_econn > /tmp/inst_econn && chmod 770 /tmp/inst_econn && /tmp/inst_econn

Or "copy and past" the following script block from "Spoiler" to your Firewall Gateway (in expert mode):

Click to Expand

cat <<EOT > /usr/bin/econn
#!/bin/bash
VERSION="4.0";
SHOW_CONN="0";
SHOW_GROUPED="0";
SHOW_IP="0";
DEL_CONN="0";
SUCHEN="";
FILTER_GREP="-v 'fgsdg'";
ENTRIE_GREP="-v 'hgdfk'";
FILE_Y="0";
FILE_FY="0";
SHOW_SUM="1";
echo "" > /tmp/econn_ip.txt
clear;
echo -e "\e[7m";printf '%.s ' {1..132}; echo;
echo  " Real time connection table analysis                                                                by Heiko Ankenbrand 2021 (v\$VERSION) ";
printf '%.s ' {1..132};echo -e "\e[0m";
IsGATEWAY=`cpprod_util FwIsFirewallModule`;
if [ \$IsGATEWAY != "1" ] ;
  then 
    echo ;
    echo "This is not a gateway!";
    echo ;
    exit 1;
fi
while [[ \$# -gt 0 ]]
do
key1="\$1"
case \$key1 in
    -h|--help.)
       shift;
       echo;
       echo -e "\e[6m";echo -n " Help overview";printf '%.s ' {1..118};echo -e "\e[0m";
       echo 
       echo "Filter Syntax"
       echo "   -a                           Show the information about the complete connection table.";
       echo "   -r <rule number>             Show the information about a specific rule with the corresponding rule number.";
       echo "   -p <port>                    Show the information about a specific destination port with the corresponding port number.";
       echo "   -d <destination IP>          Show the information about a specific destination IP with the corresponding IP.";
       echo "   -d <dIP_start-dIP_end>       Show the information about a specific destination IP range with the corresponding IP.";
       echo "   -s <source IP>               Show the information about a specific source IP with the corresponding IP.";
       echo "   -g <grep parameter>          Filters the search for the corresponding grep parameters.";
       echo ;
       echo "Output extension";
       echo "   -c                           Shows the corresponding connection table entries.";
       echo "   -e                           Is an option that sets a grep filter only on the output of the connection table view.";
       echo "   -t                           Display possible class C and B networks where the corresponding IP addresses from ";
       echo "                                the connection table would match. This function is good to simplify rules.";
       echo "   -i                           Displays only the summarized IP communication. Also used to simplify the set of rules.";
       echo "   -n                           No summary output";
       echo ;
       echo "Delete connection";
       echo "   -x                           Attention!!! This parameter deletes all connections from the connection table that match the "
       echo "                                             filters. Grep parameters (-g) cannot be deleted in the combination with this option.";
       echo "File";
       echo "   -w <file name>               Write connection table to file.";
       echo "   -f <file name>               Read connection table from file."; 
       echo "                                Important!";
       echo "                                Search filters only work when writing the file -w not with the option -f.";
       echo -e "\e[6m";echo -n " Examples";printf '%.s ' {1..123};echo -e "\e[0m";
       echo "# econn -r 10 -c                Shows all basic informations (used Ports, counter TCP/UDP/ICMP...) to rule 10 and displays";
       echo "                                the appropriate connection table entries.";
       echo "# econn -a                      Gives an overview of all connectiontabel entries (used ports, used protocols and counter";
       echo "                                TCP/UDP/ICMP...)";
       echo "# econn -p 443 -c               Displays all rules where port 443 is used and prints all connection table entries.";
       echo "# econn -d 1.1.1.1 -c           Displays all rules where destination IP 1.1.1.1 is used and gives an overview of all ";
       echo "                                connection table entries (used ports, used protocols and counter TCP/UDP/ICMP...) and";
       echo "                                prints all connection table entries.";
       echo "# econn -s 1.1.1.1 -c           Displays all rules where source IP 1.1.1.1 is used and gives an overview of all connection";
       echo "                                table entries (used ports, used protocols and counter TCP/UDP/ICMP...) and prints all";
       echo "                                connection table entries.";   
       echo "# econn -s 1.1.1.0-1.1.1.255    Displays all rules where source IP range from 1.1.1.1 to 1.1.1.255.";
       echo "# econn -r 10 -t -i             Shows all basic informations to rule 10 and summarizes all IP addresses to possible";
       echo "                                class C and B networks and output the IP communication summed by source IP's.";
       echo "# econn -p 80 -t -i -c          Shows all possible informations to port 80 in the connection table: rules, connection ";
       echo "                                summaries, used protocols and ports, grouped networks, IP communication.";
       echo "# econn -p 443 -g SYN -c        Shows all possible informations to port 443 in the connection table with 'TCP SYN' state";
       echo "# econn -r 10 -p 53 -x          Attention!!! Delete all possible connections with port 53 in rule 10 in the connection table.";
       echo "# econn -w test -p 433          Write the connection table to tar file where port 443 is used.";
       echo "# econn -f test                 Read the connection table from tar file and show the output.";
       echo "# econn -f test -c -e SYN       Read the connection table from tar file and show the output with the filter view option for SYN.";
       echo "# econn -n -p 443 -e SYN_SENT   Don't show the connection summary + show connection table for port 443 and TCP state SYN.";
       echo;
       exit 1;
    ;;
    -x|-del)
       shift;
       SHOW_CONN="1";
       DEL_CONN="1";
    ;;
    -n)
       shift;
       SHOW_SUM="0";
       SHOW_CONN="1";
    ;;
    -s|--sip)
       key="\$2";
       FILTER="\$FILTER -sip=\$key";
       SUCHEN="\$SUCHEN Source IP=\$key ";
       shift;
       shift;
    ;; 
    -d|--dip)
       key="\$2";
       FILTER="\$FILTER -dip=\$key"; 
       SUCHEN="\${SUCHEN}Destination IP=\$key ";
       shift;
       shift;
    ;;
    -p|--port)
       key="\$2";
       FILTER="\$FILTER -dport=\$key";
       SUCHEN="\${SUCHEN}DPort=\$key ";
       shift;
       shift;
    ;;
    -a|--all)
       key="\$2";
       FILTER="";
       SUCHEN="Complete connection table!";
       shift;
    ;;
    -r|--role)
       key="\$2";
       FILTER="\$FILTER -rule=\$key"; 
       SUCHEN="\${SUCHEN}Rule=\$key ";
       shift;
       shift;
    ;;
    -g|--grep)
       key="\$2";
       FILTER_GREP="\$key"; 
       SUCHEN="\${SUCHEN}GREP='\$key' ";
       shift;
       shift;
    ;;
    -e)
       ENTRIE_GREP="\$2";
       SHOW_CONN="1";
       if [ "x\$ENTRIE_GREP" = "x" ]
         then
           echo "Parameter -e not correct set!";
           ENTRIE_GREP="-v dsfgdsj";
       fi
       shift;
       shift;
    ;;
    -t|-tip)
       shift;
       SHOW_GROUPED="1";
    ;;
    -i|-ip)
       shift;
       SHOW_IP="1";
    ;;
    -c|-conn)
       SHOW_CONN="1";
       shift;
    ;;
    -w)
       FILE_W="\$2";
       FILE_W="\${FILE_W}.tgz";
       FILE_Y="1";
       shift;
       shift;
    ;;
    -f)
       FILE_F="\$2";
       FILE_F="\${FILE_F}.tgz";
       FILE_FY="1";
       shift;
       shift;
    ;;

    *)
    POSITIONAL+=("\$1") # save it in an array for later
    shift # past argument
    ;;
esac
done
if [ \$FILE_FY == "1" ] ;
  then
     if test -f "\$FILE_F"; 
        then
           echo -e "\e[6m";echo -n " Read connection table from tar archive";printf '%.s ' {1..93};echo -e "\e[0m";
           echo "Read  file     : \$FILE_F";
           tar xzfP \$FILE_F;
           FILTER="";
           SUCHEN="";
           if [ ! -f /tmp/econn_ports ]; then
               echo;
               echo "File /tmp/econn_ports not found in tar!";
               echo;
               exit 1;
           fi
           if [ ! -f /tmp/econn_ip.txt ]; then
               echo;
               echo "File /tmp/econn_ip.txt not found in tar!";
               echo;
               exit 1;
           fi
           if [ ! -f /tmp/econn_if ]; then
               echo;
               echo "File /tmp/econn_if not found in tar!";
               echo;
               exit 1;
           fi
           echo -n "CT entries     : ";
           more /tmp/econn_ip.txt | wc -l;

        else 
           echo;
           echo "File \$FILE_F not exist";
           echo;
           exit 1;
     fi
  else

     fw ctl conntab \$FILTER 2>&1 |grep \$FILTER_GREP | grep -v "Got NULL" |grep -v "gen_services_array Failed" | egrep -v '^\s*$|^#' > /tmp/econn_ip.txt;
     fw ctl iflist > /tmp/econn_if;
     if test -f "\$FWDIR/state/__tmp/FW1/local.set"; then
         more \$FWDIR/state/__tmp/FW1/local.set | grep srv_name | awk '{split(\$0,a,","); print a[1] " " a[3];}' | sed -e 's/: (\"//g' > /tmp/econn_ports;
     fi
fi

if [ \$FILE_Y == "1" ] ;
  then
   echo -e "\e[6m";echo -n " Write connection table to tar archive";printf '%.s ' {1..94};echo -e "\e[0m";
   echo -n "Search filter            : \$SUCHEN";
   tar -czf \$FILE_W -P /tmp/econn_ip.txt /tmp/econn_if /tmp/econn_ports;
   echo;
   echo -n "Connection table entries : ";
   more /tmp/econn_ip.txt | wc -l;
   echo "Written in file          : \$FILE_W";
   echo ;
   exit 1;
fi
if [ \$SHOW_SUM == "1" ] ;
  then 
echo -e "\e[6m";echo -n " Connection Summary";printf '%.s ' {1..113};echo -e "\e[0m";
echo -n "Search         : \$SUCHEN";
vsx_system=\`fw vsx stat 2>&1 | grep -c "VSX is not supported"\`
echo ;
if [ \$vsx_system == "0" ] 
     then
        echo -n "VSX VS         : ";
        vsx_vsenv1=\`vsx get | awk '{split(\$0,a,"("); sub(/ID /, "", a[2]); sub(/)./, "", a[2]);  print a[2]; }'\`
        echo "\$vsx_vsenv1"
fi 
echo -n "Rules          : ";
more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%s, \n", \$1}' 2>&1 | grep -v -E '^[1-9][0-9][0-9][0-9][0-9][0-9]' |grep -v '0,' | sort -n | uniq | tr -d '\n' | sed -e 's/0000002f/GRE/g' | sed -e 's/00000070/VRRP/g' | sed 's/\(.*\),/\1\t/' | sed -e 's/^, //g'  
echo ;
echo -n "Protocoll      : ";
more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%s, \n", \$6}' 2>&1 | sort -n | uniq | tr -d '\n' | sed -e 's/0000002f/GRE/g' | sed -e 's/00000070/VRRP/g' | sed 's/\(.*\),/\1\t/' | sed -e 's/^, //g'
echo;
echo -n "Used Ports     : ";
more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%s %s, \n", \$5, \$6}' 2>&1 | sort -n | uniq | tr -d '\n' | sed -e 's/0000002f/GRE/g' | sed -e 's/00000070/VRRP/g' | sed 's/\(.*\),/\1\t/' | sed -e 's/^ , //g' | sed -e 's/0 ICMP, //g' | sed -e 's/0 IGMP, //g' | sed -e 's/0 VRRP, //g'
echo -e "\n\e[6m";echo -n " Counter";printf '%.s ' {1..124};echo -e "\e[0m";
echo -n '  TCP          : ';more /tmp/econn_ip.txt | grep 'TCP' |wc -l;
echo -n '  TCP  SYN     : ';more /tmp/econn_ip.txt | grep 'SYN_SENT' |wc -l;
echo -n '     SYN-ACK   : ';more /tmp/econn_ip.txt | grep 'SYN_ACK' |wc -l;
echo -n '     ACK       : ';more /tmp/econn_ip.txt | grep 'ESTAB' |wc -l;
echo -n '     FIN       : ';more /tmp/econn_ip.txt | grep 'FIN' |wc -l;
echo -n '  UDP          : ';more /tmp/econn_ip.txt | grep 'UDP' |wc -l
echo -n '  ICMP         : ';more /tmp/econn_ip.txt | grep 'ICMP' |wc -l;
echo -n '  IGMP         : ';more /tmp/econn_ip.txt | grep 'IGMP' |wc -l;
echo -n '  VRRP         : ';more /tmp/econn_ip.txt | grep '00000070)' |wc -l; 
echo -n '  GRE          : ';more /tmp/econn_ip.txt | grep '0000002f)' |wc -l;
echo -e "\e[6m";echo -n " Interface";printf '%.s ' {1..122};echo -e "\e[0m";
echo -n "Incomming      : ";
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ;print b[4];}' |grep in | sort |uniq > /tmp/econn_in
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ;print b[5];}' |grep in | sort |uniq >> /tmp/econn_in 
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ;print b[6];}' |grep in | sort |uniq >> /tmp/econn_in
more /tmp/econn_in | sort |uniq| awk '{split(\$1,c,"=") ;system("cat /tmp/econn_if |grep ^"c[2] ); }' |  awk '{split(\$0,d,":") ;print "," d[2] ;}' |sort | uniq| tr -d '\n' | sed -e 's/^, //g'
echo
echo -n "Outgoing       : ";
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ;print b[4];}' |grep out | sort |uniq > /tmp/econn_out
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ;print b[5];}' |grep out | sort |uniq >> /tmp/econn_out 
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ;print b[6];}' |grep out | sort |uniq >> /tmp/econn_out
more /tmp/econn_out | sort |uniq| awk '{split(\$1,c,"=") ;system("cat /tmp/econn_if |grep ^"c[2] ); }' |  awk '{split(\$0,d,":") ;print "," d[2] ;}' |sort |uniq | tr -d '\n' | sed -e 's/^, //g'
echo
echo -e "\e[6m";echo -n " Services";printf '%.s ' {1..123};echo -e "\e[0m";
echo -n "CP Service     : ";
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ; print b[3];}' |grep service |grep -v "(" | sort |uniq > /tmp/econn_service_used
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' |  awk '{split(\$0,b,",") ; print b[4];}' |grep service |grep -v "(" | sort |uniq >> /tmp/econn_service_used
more /tmp/econn_service_used | sort |uniq| awk '{split(\$1,c,"=") ;system("cat /tmp/econn_ports |grep ^"c[2] ); }' | awk '{split(\$0,b," ") ; print ", " b[2];}' | tr -d '\n' | sed -e 's/^, //g' > /tmp/econn_service_used_all 
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ; print b[3];}' |grep service |grep  "(" |sort |uniq | awk '{split(\$1,s2,"("); sub(/)/, "[[:blank:]]",s2[2]); service_id="^"s2[2]; system("cat /tmp/econn_ports |egrep "service_id)}' |awk '{split(\$0,b," ") ; print ", " b[2];}' | tr -d '\n' >> /tmp/econn_service_used_all
more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ; print b[4];}' |grep service |grep  "(" |sort |uniq | awk '{split(\$1,s2,"("); sub(/)/, "[[:blank:]]",s2[2]); service_id="^"s2[2]; system("cat /tmp/econn_ports |egrep "service_id)}' |awk '{split(\$0,b," ") ; print ", " b[2];}' | tr -d '\n' >> /tmp/econn_service_used_all
more /tmp/econn_service_used_all | sed -e 's/, FW1_omi-sic(40)//g' | sed -e 's/^, //g'
echo


fi

if [ \$SHOW_CONN == "1" ] ;
  then
    echo -e "\e[6m";echo -n " Connection Table";printf '%.s ' {1..115};echo -e "\e[0m";
    echo -e "\nRule     Proto        Source IP         S-Port   Destination IP         D-Port     Timeout            State   Interface in   Interface out      Service";
    printf '%.s-' {1..160};
    echo;
    more /tmp/econn_ip.txt | egrep -v '^\s*$|^#'| awk -f /opt/etool/script/econn_awk1 -v vsx_system="\$vsx_system" | sort -n | sed 's/^[1-9][0-9][0-9][0-9][0-9][0-9]/-imp->/g' | grep \$ENTRIE_GREP;
fi
if [ \$SHOW_GROUPED == "1" ] ;
  then
    echo -e "\e[6m";echo -n " Grouped by";printf '%.s ' {1..121};echo -e "\e[0m";
    # printf '%.s-' {1..50};echo -e "\nGrouped by ";printf '%.s-' {1..50};
    echo -e "\nSource Class C Networks:";
    more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$2,a,"."); printf "\t%s.%s.%s.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g'
    echo -e "\nSource Class B Networks:";
    more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$2,a,"."); printf "\t%s.%s.0.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq  | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g'      
    echo -e "\nDestination Class C Networks:";
    more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$4,a,"."); printf "\t%s.%s.%s.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g'     
    echo -e "\nDestination Class B Networks:";
    more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$4,a,"."); printf "\t%s.%s.0.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g'
fi
if [ \$SHOW_IP == "1" ] ;
  then
    echo -e "\e[6m";echo -n " IP to IP";printf '%.s ' {1..124};echo -e "\e[0m\n";
    more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g'  | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%15s         -> \t%15s \n", \$2,\$4}' 2>&1 | sort -n | uniq  
fi
if [ \$DEL_CONN == "1" ] ;
  then
    OS=`cat /etc/cp-release | cut -c 17- | sed 's/^ *//g' | sed 's/\s*\$//g' | cut -c -3 | grep -c '^R8[1-9]'`
    if [[ \$OS == "1" ]] ; 
     then 
      if [[ \$FILTER_GREP == *"fgsdg"* ]] ;
        then
         echo -e "\e[6m";echo -n " Delete Connections";printf '%.s ' {1..114};echo -e "\e[0m\n";
         echo
         echo ">>>> ATTENTION <<<<"
         echo
         echo "This will clear all the connections matching the filter in the connection table!!!"
         echo -n "Are you sure (yes/no)? [n] "
         read DEL_CONN_1
         if [[ \$DEL_CONN_1 == "yes" ]] || [[ \$DEL_CONN_1 == "y" ]] ;
              then
                 echo;
                 echo -n "Are you really sure you want to do this (yes/no)? [n] "
                 FILTER="-x\$FILTER";
                    if [ -f /var/log/econn_delete_connections.txt ]; 
                       then
                          rm /var/log/econn_delete_connections.txt 2>&1> /dev/null;
                    fi
                 echo;
                 echo;
                 echo "###########################################################################################################";
                 echo "There is currently a bug in R81 and R80.10. This means"
                 echo "that deleting does not work correctly, because the filters"
                 echo "do not match. Therefore I have disabled the function."
                 echo;
                 echo "fw ctl contab \$FILTER";
                 echo
                 echo "More read here:"
                 echo "https://community.checkpoint.com/t5/General-Topics/fw-ctl-contab-x-issue-in-R81-10/m-p/128288#M23421"
                 echo;
                 echo "###########################################################################################################";
                 echo;
                 exit 1;
                 fw ctl conntab \$FILTER: > /var/log/econn_delete_connections.txt;
                 echo
                 more /var/log/econn_delete_connections.txt | grep "Nothing done." | sed -e 's/Are you sure (yes\/no)? \[n\] //g'
                 echo
                 echo "All deleted connections respectively the result are listed in the following file:"
                 echo "/var/log/econn_delete_connections.txt";
                 else
                 echo
                 echo "Nothing done.";
         fi
        else
         echo
         echo "You have set grep filter. This does not work with deleting the connections!";
         echo
         echo "Nothing done.";
      fi
     else
        echo "-x is only posible in R81 and above!"
  fi
fi 
echo;
EOT
[ -d "/opt/etool" ]  || mkdir /opt/etool;
[ -d "/opt/etool/script" ]  || mkdir /opt/etool/script; 
cat <<EOT > /opt/etool/script/econn_awk1
{
where=match(\$4, "TCP");
if (where !=0) {  rule=\$6 ; state=\$8; service=\$9 ; timer =\$5 ; proto="TCP"; dst=\$3; src=\$2; if_in=\$10;if_out=\$11; where=match(\$13, "out");  if (where !=0) {if_out=\$13 } } ;
where=match(\$4, "UDP");
if (where !=0) {  rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="UDP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9; where=match(\$11, "out");  if (where !=0) {if_out=\$11 } } ;
where=match(\$4, "0000002f");
if (where !=0) {  rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="GRE"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9} ;
where=match(\$4, "00000070");
if (where !=0) {  rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="VRRP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9}   ;
where=match(\$4, "ICMP");
if (where !=0) {  rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="ICMP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9; where=match(\$11, "out");  if (where !=0) {if_out=\$11 } };
where=match(\$4, "IGMP");
if (where !=0) {  rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="IGMP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9; where=match(\$11, "out");  if (where !=0) {if_out=\$11 } };
split(service,s,"=");
service=s[2];
sub(/,/, "", service);
where=match(\$service, ")");
if (where !=0) {split(service,s1,"("); service=s1[2];sub(/)/, "", service);}
split(state,h,"=");
state=h[2];
split(rule,h,"=");
rule=h[2];
where=match(\$9, "in");
if (where !=0) { if_in=\$9};
where=match(\$10, "in");
if (where !=0) { if_in=\$10};
where=match(\$11, "in");
if (where !=0) { if_in=\$11};
where=match(\$9, "out");
if (where !=0) { if_out=\$9};
where=match(\$10, "out");
if (where !=0) { if_out=\$10};
where=match(\$11, "out");
if (where !=0) { if_out=\$11};
where=match(\$12, "out");
if (where !=0) { if_out=\$12};
where=match(\$13, "out");
if (where !=0) { if_out=\$13};
split(if_in,h,"=");
if_in=h[2];
split(if_out,h,"=");
if_out=h[2];
split(src,h,"=");
split(h[2],h1,",");
src_ip=h1[1];
src_p=h1[2] ;
split(dst,h,"=");
split(h[2],h1,",");
dst_ip=h1[1];
dst_p=h1[2];
sub(/TCP_ESTABLISHED/, "ESTABLISHED", state);
sub(/,/, "", state);
sub(/,/, "", rule);
sub(/,/, "", timer);
sub(/,/, "", service);
sub(/\[/, "", src_ip);
sub(/\[/, "", dst_ip);
sub(/\]/, "", src_p);
sub(/\]/, "", dst_p);
sub(/,/, "", if_in);
sub(/,/, "", if_out);
read_file_into_array("/tmp/econn_if", File);
where=match(\$service, ")");
if (where ==0) {
read_file_into_array1("/tmp/econn_ports", File1);
service_last=File1[service];
}
else {
service_last=service;
}
if_out_last=File[if_out];
if (length(if_out_last) <= 0) {if_out_last="---";}
if_in_last=File[if_in];
if (length(if_in_last) <= 0) {if_in_last="---";}
if (length(service_last) <= 0) {service_last="---";}
if (proto == "icmp") { dst_p="---"; src_p="---"; }
printf "%.6s \t%6s \t%15s \t%6s \t%15s \t%6s \t%10s \t%11s \t%10s \t%10s \t%.15s \n", rule, proto, src_ip, src_p, dst_ip, dst_p, timer, state , if_in_last, if_out_last, service_last ;
service="";
rule="";
timer="";
state="";
proto="" ;
dst="" ;
src="";
if_in="";
if_out="";
}
function read_file_into_array(file, array     ,status, record, count ) {
   count  = 0;
   while (1) {
      status = getline record < file
      if (status == -1) {
         print "Failed to read file " file;
         exit 1;
      }
      if (status == 0) break;
      split(record,r,":");
      sub(/ /, "", r[1]);
      array[r[1]] = r[2];
   }
   close(file);
   return count
}
function read_file_into_array1(file, array     ,status, record, count ) {
   count  = 0;
   while (1) {
      status = getline record < file
      if (status == -1) {
         print "Failed to read file " file;
         exit 1;
      }
      if (status == 0) break;
      split(record,r," ");
      sub(/ /, "", r[1]);
      array[r[1]] = r[2];
   }
   close(file);
   return count
}
EOT
chmod 770 /usr/bin/econn
chmod 770 /opt/etool/script/econn_awk1

cat <<EOT > /usr/bin/econn #!/bin/bash VERSION="4.0"; SHOW_CONN="0"; SHOW_GROUPED="0"; SHOW_IP="0"; DEL_CONN="0"; SUCHEN=""; FILTER_GREP="-v 'fgsdg'"; ENTRIE_GREP="-v 'hgdfk'"; FILE_Y="0"; FILE_FY="0"; SHOW_SUM="1"; echo "" > /tmp/econn_ip.txt clear; echo -e "\e[7m";printf '%.s ' {1..132}; echo; echo " Real time connection table analysis by Heiko Ankenbrand 2021 (v\$VERSION) "; printf '%.s ' {1..132};echo -e "\e[0m"; IsGATEWAY=`cpprod_util FwIsFirewallModule`; if [ \$IsGATEWAY != "1" ] ; then echo ; echo "This is not a gateway!"; echo ; exit 1; fi while [[ \$# -gt 0 ]] do key1="\$1" case \$key1 in -h|--help.) shift; echo; echo -e "\e[6m";echo -n " Help overview";printf '%.s ' {1..118};echo -e "\e[0m"; echo echo "Filter Syntax" echo " -a Show the information about the complete connection table."; echo " -r <rule number> Show the information about a specific rule with the corresponding rule number."; echo " -p <port> Show the information about a specific destination port with the corresponding port number."; echo " -d <destination IP> Show the information about a specific destination IP with the corresponding IP."; echo " -d <dIP_start-dIP_end> Show the information about a specific destination IP range with the corresponding IP."; echo " -s <source IP> Show the information about a specific source IP with the corresponding IP."; echo " -g <grep parameter> Filters the search for the corresponding grep parameters."; echo ; echo "Output extension"; echo " -c Shows the corresponding connection table entries."; echo " -e Is an option that sets a grep filter only on the output of the connection table view."; echo " -t Display possible class C and B networks where the corresponding IP addresses from "; echo " the connection table would match. This function is good to simplify rules."; echo " -i Displays only the summarized IP communication. Also used to simplify the set of rules."; echo " -n No summary output"; echo ; echo "Delete connection"; echo " -x Attention!!! This parameter deletes all connections from the connection table that match the " echo " filters. Grep parameters (-g) cannot be deleted in the combination with this option."; echo "File"; echo " -w <file name> Write connection table to file."; echo " -f <file name> Read connection table from file."; echo " Important!"; echo " Search filters only work when writing the file -w not with the option -f."; echo -e "\e[6m";echo -n " Examples";printf '%.s ' {1..123};echo -e "\e[0m"; echo "# econn -r 10 -c Shows all basic informations (used Ports, counter TCP/UDP/ICMP...) to rule 10 and displays"; echo " the appropriate connection table entries."; echo "# econn -a Gives an overview of all connectiontabel entries (used ports, used protocols and counter"; echo " TCP/UDP/ICMP...)"; echo "# econn -p 443 -c Displays all rules where port 443 is used and prints all connection table entries."; echo "# econn -d 1.1.1.1 -c Displays all rules where destination IP 1.1.1.1 is used and gives an overview of all "; echo " connection table entries (used ports, used protocols and counter TCP/UDP/ICMP...) and"; echo " prints all connection table entries."; echo "# econn -s 1.1.1.1 -c Displays all rules where source IP 1.1.1.1 is used and gives an overview of all connection"; echo " table entries (used ports, used protocols and counter TCP/UDP/ICMP...) and prints all"; echo " connection table entries."; echo "# econn -s 1.1.1.0-1.1.1.255 Displays all rules where source IP range from 1.1.1.1 to 1.1.1.255."; echo "# econn -r 10 -t -i Shows all basic informations to rule 10 and summarizes all IP addresses to possible"; echo " class C and B networks and output the IP communication summed by source IP's."; echo "# econn -p 80 -t -i -c Shows all possible informations to port 80 in the connection table: rules, connection "; echo " summaries, used protocols and ports, grouped networks, IP communication."; echo "# econn -p 443 -g SYN -c Shows all possible informations to port 443 in the connection table with 'TCP SYN' state"; echo "# econn -r 10 -p 53 -x Attention!!! Delete all possible connections with port 53 in rule 10 in the connection table."; echo "# econn -w test -p 433 Write the connection table to tar file where port 443 is used."; echo "# econn -f test Read the connection table from tar file and show the output."; echo "# econn -f test -c -e SYN Read the connection table from tar file and show the output with the filter view option for SYN."; echo "# econn -n -p 443 -e SYN_SENT Don't show the connection summary + show connection table for port 443 and TCP state SYN."; echo; exit 1; ;; -x|-del) shift; SHOW_CONN="1"; DEL_CONN="1"; ;; -n) shift; SHOW_SUM="0"; SHOW_CONN="1"; ;; -s|--sip) key="\$2"; FILTER="\$FILTER -sip=\$key"; SUCHEN="\$SUCHEN Source IP=\$key "; shift; shift; ;; -d|--dip) key="\$2"; FILTER="\$FILTER -dip=\$key"; SUCHEN="\${SUCHEN}Destination IP=\$key "; shift; shift; ;; -p|--port) key="\$2"; FILTER="\$FILTER -dport=\$key"; SUCHEN="\${SUCHEN}DPort=\$key "; shift; shift; ;; -a|--all) key="\$2"; FILTER=""; SUCHEN="Complete connection table!"; shift; ;; -r|--role) key="\$2"; FILTER="\$FILTER -rule=\$key"; SUCHEN="\${SUCHEN}Rule=\$key "; shift; shift; ;; -g|--grep) key="\$2"; FILTER_GREP="\$key"; SUCHEN="\${SUCHEN}GREP='\$key' "; shift; shift; ;; -e) ENTRIE_GREP="\$2"; SHOW_CONN="1"; if [ "x\$ENTRIE_GREP" = "x" ] then echo "Parameter -e not correct set!"; ENTRIE_GREP="-v dsfgdsj"; fi shift; shift; ;; -t|-tip) shift; SHOW_GROUPED="1"; ;; -i|-ip) shift; SHOW_IP="1"; ;; -c|-conn) SHOW_CONN="1"; shift; ;; -w) FILE_W="\$2"; FILE_W="\${FILE_W}.tgz"; FILE_Y="1"; shift; shift; ;; -f) FILE_F="\$2"; FILE_F="\${FILE_F}.tgz"; FILE_FY="1"; shift; shift; ;; *) POSITIONAL+=("\$1") # save it in an array for later shift # past argument ;; esac done if [ \$FILE_FY == "1" ] ; then if test -f "\$FILE_F"; then echo -e "\e[6m";echo -n " Read connection table from tar archive";printf '%.s ' {1..93};echo -e "\e[0m"; echo "Read file : \$FILE_F"; tar xzfP \$FILE_F; FILTER=""; SUCHEN=""; if [ ! -f /tmp/econn_ports ]; then echo; echo "File /tmp/econn_ports not found in tar!"; echo; exit 1; fi if [ ! -f /tmp/econn_ip.txt ]; then echo; echo "File /tmp/econn_ip.txt not found in tar!"; echo; exit 1; fi if [ ! -f /tmp/econn_if ]; then echo; echo "File /tmp/econn_if not found in tar!"; echo; exit 1; fi echo -n "CT entries : "; more /tmp/econn_ip.txt | wc -l; else echo; echo "File \$FILE_F not exist"; echo; exit 1; fi else fw ctl conntab \$FILTER 2>&1 |grep \$FILTER_GREP | grep -v "Got NULL" |grep -v "gen_services_array Failed" | egrep -v '^\s*$|^#' > /tmp/econn_ip.txt; fw ctl iflist > /tmp/econn_if; if test -f "\$FWDIR/state/__tmp/FW1/local.set"; then more \$FWDIR/state/__tmp/FW1/local.set | grep srv_name | awk '{split(\$0,a,","); print a[1] " " a[3];}' | sed -e 's/: (\"//g' > /tmp/econn_ports; fi fi if [ \$FILE_Y == "1" ] ; then echo -e "\e[6m";echo -n " Write connection table to tar archive";printf '%.s ' {1..94};echo -e "\e[0m"; echo -n "Search filter : \$SUCHEN"; tar -czf \$FILE_W -P /tmp/econn_ip.txt /tmp/econn_if /tmp/econn_ports; echo; echo -n "Connection table entries : "; more /tmp/econn_ip.txt | wc -l; echo "Written in file : \$FILE_W"; echo ; exit 1; fi if [ \$SHOW_SUM == "1" ] ; then echo -e "\e[6m";echo -n " Connection Summary";printf '%.s ' {1..113};echo -e "\e[0m"; echo -n "Search : \$SUCHEN"; vsx_system=\`fw vsx stat 2>&1 | grep -c "VSX is not supported"\` echo ; if [ \$vsx_system == "0" ] then echo -n "VSX VS : "; vsx_vsenv1=\`vsx get | awk '{split(\$0,a,"("); sub(/ID /, "", a[2]); sub(/)./, "", a[2]); print a[2]; }'\` echo "\$vsx_vsenv1" fi echo -n "Rules : "; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%s, \n", \$1}' 2>&1 | grep -v -E '^[1-9][0-9][0-9][0-9][0-9][0-9]' |grep -v '0,' | sort -n | uniq | tr -d '\n' | sed -e 's/0000002f/GRE/g' | sed -e 's/00000070/VRRP/g' | sed 's/$.*$,/\1\t/' | sed -e 's/^, //g' echo ; echo -n "Protocoll : "; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%s, \n", \$6}' 2>&1 | sort -n | uniq | tr -d '\n' | sed -e 's/0000002f/GRE/g' | sed -e 's/00000070/VRRP/g' | sed 's/$.*$,/\1\t/' | sed -e 's/^, //g' echo; echo -n "Used Ports : "; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%s %s, \n", \$5, \$6}' 2>&1 | sort -n | uniq | tr -d '\n' | sed -e 's/0000002f/GRE/g' | sed -e 's/00000070/VRRP/g' | sed 's/$.*$,/\1\t/' | sed -e 's/^ , //g' | sed -e 's/0 ICMP, //g' | sed -e 's/0 IGMP, //g' | sed -e 's/0 VRRP, //g' echo -e "\n\e[6m";echo -n " Counter";printf '%.s ' {1..124};echo -e "\e[0m"; echo -n ' TCP : ';more /tmp/econn_ip.txt | grep 'TCP' |wc -l; echo -n ' TCP SYN : ';more /tmp/econn_ip.txt | grep 'SYN_SENT' |wc -l; echo -n ' SYN-ACK : ';more /tmp/econn_ip.txt | grep 'SYN_ACK' |wc -l; echo -n ' ACK : ';more /tmp/econn_ip.txt | grep 'ESTAB' |wc -l; echo -n ' FIN : ';more /tmp/econn_ip.txt | grep 'FIN' |wc -l; echo -n ' UDP : ';more /tmp/econn_ip.txt | grep 'UDP' |wc -l echo -n ' ICMP : ';more /tmp/econn_ip.txt | grep 'ICMP' |wc -l; echo -n ' IGMP : ';more /tmp/econn_ip.txt | grep 'IGMP' |wc -l; echo -n ' VRRP : ';more /tmp/econn_ip.txt | grep '00000070)' |wc -l; echo -n ' GRE : ';more /tmp/econn_ip.txt | grep '0000002f)' |wc -l; echo -e "\e[6m";echo -n " Interface";printf '%.s ' {1..122};echo -e "\e[0m"; echo -n "Incomming : "; more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ;print b[4];}' |grep in | sort |uniq > /tmp/econn_in more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ;print b[5];}' |grep in | sort |uniq >> /tmp/econn_in more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ;print b[6];}' |grep in | sort |uniq >> /tmp/econn_in more /tmp/econn_in | sort |uniq| awk '{split(\$1,c,"=") ;system("cat /tmp/econn_if |grep ^"c[2] ); }' | awk '{split(\$0,d,":") ;print "," d[2] ;}' |sort | uniq| tr -d '\n' | sed -e 's/^, //g' echo echo -n "Outgoing : "; more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ;print b[4];}' |grep out | sort |uniq > /tmp/econn_out more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ;print b[5];}' |grep out | sort |uniq >> /tmp/econn_out more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ;print b[6];}' |grep out | sort |uniq >> /tmp/econn_out more /tmp/econn_out | sort |uniq| awk '{split(\$1,c,"=") ;system("cat /tmp/econn_if |grep ^"c[2] ); }' | awk '{split(\$0,d,":") ;print "," d[2] ;}' |sort |uniq | tr -d '\n' | sed -e 's/^, //g' echo echo -e "\e[6m";echo -n " Services";printf '%.s ' {1..123};echo -e "\e[0m"; echo -n "CP Service : "; more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ; print b[3];}' |grep service |grep -v "(" | sort |uniq > /tmp/econn_service_used more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ; print b[4];}' |grep service |grep -v "(" | sort |uniq >> /tmp/econn_service_used more /tmp/econn_service_used | sort |uniq| awk '{split(\$1,c,"=") ;system("cat /tmp/econn_ports |grep ^"c[2] ); }' | awk '{split(\$0,b," ") ; print ", " b[2];}' | tr -d '\n' | sed -e 's/^, //g' > /tmp/econn_service_used_all more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ; print b[3];}' |grep service |grep "(" |sort |uniq | awk '{split(\$1,s2,"("); sub(/)/, "[[:blank:]]",s2[2]); service_id="^"s2[2]; system("cat /tmp/econn_ports |egrep "service_id)}' |awk '{split(\$0,b," ") ; print ", " b[2];}' | tr -d '\n' >> /tmp/econn_service_used_all more /tmp/econn_ip.txt | awk '{split(\$0,a,";"); print a[2];}' | awk '{split(\$0,b,",") ; print b[4];}' |grep service |grep "(" |sort |uniq | awk '{split(\$1,s2,"("); sub(/)/, "[[:blank:]]",s2[2]); service_id="^"s2[2]; system("cat /tmp/econn_ports |egrep "service_id)}' |awk '{split(\$0,b," ") ; print ", " b[2];}' | tr -d '\n' >> /tmp/econn_service_used_all more /tmp/econn_service_used_all | sed -e 's/, FW1_omi-sic(40)//g' | sed -e 's/^, //g' echo fi if [ \$SHOW_CONN == "1" ] ; then echo -e "\e[6m";echo -n " Connection Table";printf '%.s ' {1..115};echo -e "\e[0m"; echo -e "\nRule Proto Source IP S-Port Destination IP D-Port Timeout State Interface in Interface out Service"; printf '%.s-' {1..160}; echo; more /tmp/econn_ip.txt | egrep -v '^\s*$|^#'| awk -f /opt/etool/script/econn_awk1 -v vsx_system="\$vsx_system" | sort -n | sed 's/^[1-9][0-9][0-9][0-9][0-9][0-9]/-imp->/g' | grep \$ENTRIE_GREP; fi if [ \$SHOW_GROUPED == "1" ] ; then echo -e "\e[6m";echo -n " Grouped by";printf '%.s ' {1..121};echo -e "\e[0m"; # printf '%.s-' {1..50};echo -e "\nGrouped by ";printf '%.s-' {1..50}; echo -e "\nSource Class C Networks:"; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$2,a,"."); printf "\t%s.%s.%s.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g' echo -e "\nSource Class B Networks:"; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$2,a,"."); printf "\t%s.%s.0.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g' echo -e "\nDestination Class C Networks:"; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$4,a,"."); printf "\t%s.%s.%s.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g' echo -e "\nDestination Class B Networks:"; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$4,a,"."); printf "\t%s.%s.0.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g' fi if [ \$SHOW_IP == "1" ] ; then echo -e "\e[6m";echo -n " IP to IP";printf '%.s ' {1..124};echo -e "\e[0m\n"; more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/)\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#' | awk '{printf "%15s -> \t%15s \n", \$2,\$4}' 2>&1 | sort -n | uniq fi if [ \$DEL_CONN == "1" ] ; then OS=`cat /etc/cp-release | cut -c 17- | sed 's/^ *//g' | sed 's/\s*\$//g' | cut -c -3 | grep -c '^R8[1-9]'` if [[ \$OS == "1" ]] ; then if [[ \$FILTER_GREP == *"fgsdg"* ]] ; then echo -e "\e[6m";echo -n " Delete Connections";printf '%.s ' {1..114};echo -e "\e[0m\n"; echo echo ">>>> ATTENTION <<<<" echo echo "This will clear all the connections matching the filter in the connection table!!!" echo -n "Are you sure (yes/no)? [n] " read DEL_CONN_1 if [[ \$DEL_CONN_1 == "yes" ]] || [[ \$DEL_CONN_1 == "y" ]] ; then echo; echo -n "Are you really sure you want to do this (yes/no)? [n] " FILTER="-x\$FILTER"; if [ -f /var/log/econn_delete_connections.txt ]; then rm /var/log/econn_delete_connections.txt 2>&1> /dev/null; fi echo; echo; echo "###########################################################################################################"; echo "There is currently a bug in R81 and R80.10. This means" echo "that deleting does not work correctly, because the filters" echo "do not match. Therefore I have disabled the function." echo; echo "fw ctl contab \$FILTER"; echo echo "More read here:" echo "https://community.checkpoint.com/t5/General-Topics/fw-ctl-contab-x-issue-in-R81-10/m-p/128288#M23421" echo; echo "###########################################################################################################"; echo; exit 1; fw ctl conntab \$FILTER: > /var/log/econn_delete_connections.txt; echo more /var/log/econn_delete_connections.txt | grep "Nothing done." | sed -e 's/Are you sure (yes\/no)? \[n\] //g' echo echo "All deleted connections respectively the result are listed in the following file:" echo "/var/log/econn_delete_connections.txt"; else echo echo "Nothing done."; fi else echo echo "You have set grep filter. This does not work with deleting the connections!"; echo echo "Nothing done."; fi else echo "-x is only posible in R81 and above!" fi fi echo; EOT [ -d "/opt/etool" ] || mkdir /opt/etool; [ -d "/opt/etool/script" ] || mkdir /opt/etool/script; cat <<EOT > /opt/etool/script/econn_awk1 { where=match(\$4, "TCP"); if (where !=0) { rule=\$6 ; state=\$8; service=\$9 ; timer =\$5 ; proto="TCP"; dst=\$3; src=\$2; if_in=\$10;if_out=\$11; where=match(\$13, "out"); if (where !=0) {if_out=\$13 } } ; where=match(\$4, "UDP"); if (where !=0) { rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="UDP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9; where=match(\$11, "out"); if (where !=0) {if_out=\$11 } } ; where=match(\$4, "0000002f"); if (where !=0) { rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="GRE"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9} ; where=match(\$4, "00000070"); if (where !=0) { rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="VRRP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9} ; where=match(\$4, "ICMP"); if (where !=0) { rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="ICMP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9; where=match(\$11, "out"); if (where !=0) {if_out=\$11 } }; where=match(\$4, "IGMP"); if (where !=0) { rule=\$6 ; state="state=---"; service=\$7 ; timer =\$5 ; proto="IGMP"; dst=\$3; src=\$2; if_in=\$8;if_out=\$9; where=match(\$11, "out"); if (where !=0) {if_out=\$11 } }; split(service,s,"="); service=s[2]; sub(/,/, "", service); where=match(\$service, ")"); if (where !=0) {split(service,s1,"("); service=s1[2];sub(/)/, "", service);} split(state,h,"="); state=h[2]; split(rule,h,"="); rule=h[2]; where=match(\$9, "in"); if (where !=0) { if_in=\$9}; where=match(\$10, "in"); if (where !=0) { if_in=\$10}; where=match(\$11, "in"); if (where !=0) { if_in=\$11}; where=match(\$9, "out"); if (where !=0) { if_out=\$9}; where=match(\$10, "out"); if (where !=0) { if_out=\$10}; where=match(\$11, "out"); if (where !=0) { if_out=\$11}; where=match(\$12, "out"); if (where !=0) { if_out=\$12}; where=match(\$13, "out"); if (where !=0) { if_out=\$13}; split(if_in,h,"="); if_in=h[2]; split(if_out,h,"="); if_out=h[2]; split(src,h,"="); split(h[2],h1,","); src_ip=h1[1]; src_p=h1[2] ; split(dst,h,"="); split(h[2],h1,","); dst_ip=h1[1]; dst_p=h1[2]; sub(/TCP_ESTABLISHED/, "ESTABLISHED", state); sub(/,/, "", state); sub(/,/, "", rule); sub(/,/, "", timer); sub(/,/, "", service); sub(/\[/, "", src_ip); sub(/\[/, "", dst_ip); sub(/\]/, "", src_p); sub(/\]/, "", dst_p); sub(/,/, "", if_in); sub(/,/, "", if_out); read_file_into_array("/tmp/econn_if", File); where=match(\$service, ")"); if (where ==0) { read_file_into_array1("/tmp/econn_ports", File1); service_last=File1[service]; } else { service_last=service; } if_out_last=File[if_out]; if (length(if_out_last) <= 0) {if_out_last="---";} if_in_last=File[if_in]; if (length(if_in_last) <= 0) {if_in_last="---";} if (length(service_last) <= 0) {service_last="---";} if (proto == "icmp") { dst_p="---"; src_p="---"; } printf "%.6s \t%6s \t%15s \t%6s \t%15s \t%6s \t%10s \t%11s \t%10s \t%10s \t%.15s \n", rule, proto, src_ip, src_p, dst_ip, dst_p, timer, state , if_in_last, if_out_last, service_last ; service=""; rule=""; timer=""; state=""; proto="" ; dst="" ; src=""; if_in=""; if_out=""; } function read_file_into_array(file, array ,status, record, count ) { count = 0; while (1) { status = getline record < file if (status == -1) { print "Failed to read file " file; exit 1; } if (status == 0) break; split(record,r,":"); sub(/ /, "", r[1]); array[r[1]] = r[2]; } close(file); return count } function read_file_into_array1(file, array ,status, record, count ) { count = 0; while (1) { status = getline record < file if (status == -1) { print "Failed to read file " file; exit 1; } if (status == 0) break; split(record,r," "); sub(/ /, "", r[1]); array[r[1]] = r[2]; } close(file); return count } EOT chmod 770 /usr/bin/econn chmod 770 /opt/etool/script/econn_awk1

Version

0.1   08-08-2021 -    oneliner to show all connection table entries
                                       (ONELINER - Formatted Connection Table)
0.9    08-12-2021     -    Bugs fixed
1.0    08-26-2021     -    Version v1.0 - This version only shows info about certain rules
                                       (Easy Tool - Real time rule analysis v1.0)

2.0    08-25-2021     -    New version for filtering by rule, port, dst IP and src IP
2.1    08-26-2021     -    Bugs fixed
2.2    08-27-2021     -    Add -g grep parameter
2.3    08-28-2021     -    Add -x delete parameter
                                        (This parameter is only available from R81 and higher.)
2.4    08-28-2021     -    There is currently a bug in R81 and R81.10 with "fw ctl conntab -x -rule=3"
                                        Therefore I have disabled this function -x.
                                      ('fw ctl contab -x' issue in R81.10)

2.5    09-01-2021     -    Bugs fixed (conn issue)
2.6    09-08-2021     - Incoming and outgoing interface added
2.7    09-09-2021     -    Check Point service names added
2.8b 09-09-2021     -    Bugs fixed
                                      ( --> more \$FWDIR/state/__tmp/FW1/ )
2.9    09-10-2021     -    Now with extended connection table view:
                                      incoming interface, outgoing interface, Check Point service name
2.9i   09-10-2021     -    Bugs fixed
                                        (ICMP issues, interface issue, Check Point service issue)

3.0    09-11-2021     -    VSX support
3.1    09-11-2021     -    Bugs fixed
                                        (option -g issue, VSX "fw ctl conntab" issue)
3.2    09-12-2021     -    Bugs fixed
                                        ( option -r /-s /-d /-p /-g issue)
3.3    09-13-2021     -    Design modification

4.0    09-15-2021     -    File read and write, added -n no summary output
4.0f   09-16-2021     -    Performance optimization of the script for large connection tables.
4.0g 09-23-2021     -    Add -h option
4.0h 14-11-2021     -    Performance optimization for VSX environments

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

Reimar_W · ‎2021-08-28

Hi @HeikoAnkenbrand

The script simplifies the search in the connection table.
Great idea and thanks for your great contributions.

Small note:
Unfortunately, the use of multiple filters -p 53 -d 8.8.8.8 does not work.

HeikoAnkenbrand · ‎2021-08-28

Hi @Reimar_W,

I reworked this in the script and it now works with multiple filter parameters.

Thanks
Heiko

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

udo_kimmich · ‎2021-08-28

It's really cool how you can browse with this tool in the connection tabel.
This allows you to get information quickly and easily.

Great job
@HeikoAnkenbrand

Power_Support · ‎2021-08-30

Hi @HeikoAnkenbrand,

nice solution.

What is the state "conn" in the output?

HeikoAnkenbrand · ‎2021-08-31

Hi @Power_Support

Bug is fixed in version 2.5!

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

IgorWeller · ‎2021-09-07

Very interesting tool.
Could you also provide an overview of the interfaces in use?

HeikoAnkenbrand · ‎2021-09-08

Incoming and outgoing interface added in version 2.6.

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

Svendsen · ‎2021-09-08

Great work Heiko, this will become usefull for almost everyone working with CP

HeikoAnkenbrand · ‎2021-09-08

Check Point service names added in version 2.7

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

Wolfgang · ‎2021-09-09

Great tool @HeikoAnkenbrand . How about VSX, known problems ?

HeikoAnkenbrand · ‎2021-09-09

Hi @Wolfgang,

The script is very complex and I try to integrate VSX. However, one or two functions are not yet VSX compatible.
Please give me another week or two 😉

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

fwmeister · ‎2021-09-10

Hi Heiko,

You could add a small option for the top rules using cpstat blades and take the 5 rules and show them .

Cheers

HeikoAnkenbrand · ‎2021-09-12

Hi @Wolfgang,

After a weekend with a lot of programming work I made the script VSX compatible.
You only need to run the command in a VS instance:
# vsenv xy
# econn ...

Now the VS instance should be displayed as shown in the picture:

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

Wolfgang · ‎2021-09-15

@HeikoAnkenbrand

work like a charm with VSX. Saved me a lot of time at the moment investigating a problem with some connections.

👍👍

HeikoAnkenbrand · ‎2021-09-09

From version 2.9 with extended connection table view:
+ Incoming interface
+ Outgoing interface
+ Check Point service name

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

fwmeister · ‎2021-09-10

got a few errors (r80.20 hf take188) Yes, I know it's "old". 🙂

using -t -i -c

awk: fatal: can't open source file `/opt/etool/script/econn_awk1' for reading (No such file or directory)

also

Incomming : sh: -c: line 0: syntax error near unexpected token `('
sh: -c: line 0: `cat /tmp/econn_if |grep ^domain-udp(122)'

fwmeister · ‎2021-09-10

ok. Got that /opt/etool error because I just copied the /usr/bin/econn to firewalls instead of "installing" it.

fwmeister · ‎2021-09-10

Excellent tool! Thanks for sharing!

HeikoAnkenbrand · ‎2021-09-11

Bugs fixed in version 2.9:
- ICMP issues
- interface issue
- Check Point service issue

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

KostasGR · ‎2021-09-13

Hello @HeikoAnkenbrand

In case of inline rules the -r flag doesn't seem to work. For a example for a rule 2.1,2.2 etc.

-r <rule number>

Show the information about a specific rule with the corresponding rule number.

BR,

Kostas

HeikoAnkenbrand · ‎2021-09-13

Hi @KostasGR,

I use the command "fw ctl conntab" to display the connection tab. Unfortunately this does not support inline rules. Therefore, you can only use the basic inline layer rule. Unfortunately, this cannot be changed technically.

Here is an example from my lab environment:

fw ctl conntab -r 3

Output tool

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

Henrik_Noerr1 · ‎2021-09-14

would like to try this, but I get:

/bin/econn: line 10: [[: $#: syntax error: operand expected (error token is "$#")

fw ver
This is Check Point's software version R80.40 - Build 124

uname -a
Linux hostname 3.10.0-957.21.3cpx86_64 #1 SMP Sun Apr 18 18:41:00 IDT 2021 x86_64 x86_64 x86_64 GNU/Linux

Regards,

Henrik

joschuar · ‎2021-09-14

@HeikoAnkenbrand

Great job.

HeikoAnkenbrand · ‎2021-09-14

Version 4.0 is now available with many new features:

- VSX Support
- Write connection table to file
- Read connection table from file
- No summary output (option -n)
- Search filter for the corresponding grep parameters in the connection table view output.

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

joschuar · ‎2021-09-16

Hello @HeikoAnkenbrand,

first of all a big thank you for another great tool here for the CheckMates community.
The script runs on all our gateways. It is a bit slow with more than 100K connection table entries.
But otherwise a great solution.

HeikoAnkenbrand · ‎2021-09-16

In the last few days I have spent a lot of time optimizing the code. Now even larger connection tabs should be output in a reasonable time.

From version 4.0e I will optimize the script code a bit more.

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

HeikoAnkenbrand · ‎2021-09-22

In the latest version 4.0g the script is performance optimized. Therefore, connection tabs larger than 100K can be displayed quickly.

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips

genisis__ · ‎2021-11-14

Hi Heiko, Just tried pasting in the script and got this:

Real time connection table analysis by Heiko Ankenbrand 2021 (v4.0)

/usr/bin/econn: line 308: syntax error near unexpected token `\$2,a,"."'
/usr/bin/econn: line 308: ` more /tmp/econn_ip.txt | awk '{print \$6 " "\$2 \$3 \$4 " "\$5 " "\$8}' | sed -e 's/src=//g' | sed -e 's/\],dest=\[/ /g' | sed -e 's/\],/ /g' | sed -e 's/\;//g' | sed -e 's/\[//g' | sed -e 's/rule\=/ /g' | sed -e 's/\,/ /g' | sed -e 's/state\=/ /g' | sed -e 's/Ifn[c,s]in\=[0-9]*//g' | sed -e 's/Ifn[c,s]out\=[0-9]*//g' | egrep -v '^\s*$|^#'| awk '{split(\$2,a,".")'; printf "\t%s.%s.%s.0\n", a[1],a[2],a[3]}' 2>&1 | sort -n | uniq | sed -e 's/\.\.\.0//g' | sed -e 's/\.\.0\.0//g''

Zuhal · ‎2021-10-04

Hello @HeikoAnkenbrand,

Nice tool.

I sometimes get a grep bug in the ports section!

Filters

Sort By

Categories

Easy Tool - Real time connection table analysis v4.0

Disclaimer: Check Point does not provide maintenance services or technical or customer support for third party content provided on this Site, including in CheckMates Toolbox. See also our Third Party Software Disclaimer.