Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
adrian_
Explorer
Jump to solution

Destination Host Unreachable - 8.8.8.8 (intermittent)

Hello CheckMates,

We suddenly have issues on our CheckPoint Firewall 4800 going out to internet.

It is a WIFI to our Guest and I have check the Switch, APs, WLC and our Modem(Direct connection is working)

We are associated in our WLC and it was even to provide us an IP address from WLC.

The issue is that the WIFI logo is showing with ! using our mobile

Capture.PNG

Troubleshooting Done.

1.) Reboot AP
2.) Shut/Unshut ports on switch
3.) Adjust Power Level
4.) Turn off/on the SSID
5.) No Changes on VLANs/WLC on the switch
6.) Direct Connection in the ONT – Working

Here is the result when doing a ping test to 8.8.8.8, btw we have a spare same firewall but same issue 

PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
From 10x.x.x icmp_seq=2 Destination Host Unreachable
From 10x.x.x icmp_seq=3 Destination Host Unreachable
From 10x.x.x icmp_seq=4 Destination Host Unreachable
From 10x.x.x icmp_seq=6 Destination Host Unreachable
From 10x.x.x icmp_seq=7 Destination Host Unreachable
From 10x.x.x icmp_seq=8 Destination Host Unreachable

Sometimes the firewall can ping 8.8.8.8

8.8.8.8: bytes=32 time=5ms TTL=116
8.8.8.8: bytes=32 time=4ms TTL=116
8.8.8.8: bytes=32 time=4ms TTL=116
8.8.8.8: bytes=32 time=4ms TTL=116

Diagram.PNG

 

0 Kudos
2 Solutions

Accepted Solutions
PhoneBoy
Admin
Admin

R75.40 is very, very End of Support at this point (several years now) and recommend upgrading to a supported release.

Setting a default route to point to a given interface is not recommended and could cause issues with the arp table filling up.
You only need to configure it to point to the next hop IP.
Remove that specific route.

The NAT is probably configured in the object that represents the Guest WiFI network in SmartDashboard.

View solution in original post

0 Kudos
PhoneBoy
Admin
Admin

First of all, when you remove the route, the arp cache being full should no longer be an issue, assuming there is an ARP entry for the default route.
Second, I don't believe there is a way to clear the arp cache, but it should clear on its own.

View solution in original post

0 Kudos
9 Replies
PhoneBoy
Admin
Admin

What host is generating the Destination Unreachable message?
That generally means it doesn’t have the necessary route.
How is the default route defined on the 4800?
What version/JHF is running on the 4800?

0 Kudos
adrian_
Explorer

It is intermittent, it can ping  destination and mostly it will result to host unreachable.

Interface eth2 10x.x.110 /30 

set static-route default nexthop gateway address 10x.x.x.109 priority 1 on
set static-route default nexthop gateway logical eth2 priority 1 on

This config is being used since 2018 then few days ago we experience an issue on our guest wifi.

Our version is using Check Point R75.4

0 Kudos
PhoneBoy
Admin
Admin

R75.40 is very, very End of Support at this point (several years now) and recommend upgrading to a supported release.

Setting a default route to point to a given interface is not recommended and could cause issues with the arp table filling up.
You only need to configure it to point to the next hop IP.
Remove that specific route.

The NAT is probably configured in the object that represents the Guest WiFI network in SmartDashboard.

0 Kudos
adrian_
Explorer

Hi, 

 I will remove the following config

set static-route default nexthop gateway logical eth2 priority 1 on

 

Then leave the remaining config

set static-route default nexthop gateway address 10x.x.x.109 priority 1 on

 

How do I clear the ARP cache using a cli config?

Thanks

0 Kudos
PhoneBoy
Admin
Admin

First of all, when you remove the route, the arp cache being full should no longer be an issue, assuming there is an ARP entry for the default route.
Second, I don't believe there is a way to clear the arp cache, but it should clear on its own.

0 Kudos
adrian_
Explorer

I will remove the config then hopefully it will fix the issue.

I am new using checkpoint, what is the command to remove set static-route default nexthop gateway logical eth2 priority 1 on?

 

Thanks

0 Kudos
adrian_
Explorer

Hi All,

Removing set static-route default nexthop gateway logical eth2 priority 1 on able to resolve the issue of destination host unreachable.

 

Thanks for all the help!

0 Kudos
adrian_
Explorer

This one have a NAT config from the smart console.

I am still figuring out how to access it.

 

Basically, 

The guest user segment is 192.168.10.0/24

All the wifi client will be natted to ip 10x.x.x.110 when accessing internet

0 Kudos
Vincent_Bacher
Advisor
Advisor

I would not do any troubleshooting here at all until I had carried out an update, as also recommended by Phoneboy.

and now to something completely different - CCVS, CCAS, CCTE, CCCS, CCSM elite
0 Kudos

Leaderboard

Epsum factorial non deposit quid pro quo hic escorol.

Upcoming Events

    CheckMates Events