- Products
- Learn
- Local User Groups
- Partners
- More
What’s New in Device Diagnostics?
Dec 2nd @ 5pm CET / 11am EST
AI Security Masters
Security in the Pace of AI:
From Threat to Force Multiplier
CPX is Back!
Join us in Las Vegas, Vienna, and/or Bangkok!
Check Point Named a Leader
The Forrester Wave:
Enterprise Firewall Solutions, Q4 2026
What’s New in Agentic Network Orchestration
CheckMates Go:
Fun Ding
Hey guys,
Wanted to update with something else my colleague and I discovered. So, I will give an example we used and this is with numbered vti's, since we did not want to spend too much time with troubleshooting why unnumbered did not work, plus we are not even sure its supported 🙂
Example for redundant tunnels (you need advanced license to do this, since basic one only allows for single tunnels for 1 POP, not 2 or more). Btw, since sd-wan is not supported with this yet, then load balancing the traffic among the multiple ISP links is not really an option, but from what we tested, all else seems to work fine.
loopback interface:
router ID 169.254.241.1
local as 65000
remote as 65001
peer 1 -> 169.254.100.254
peer 2 -> 169.254.200.254
fw1:
vti 1 -> 169.254.100.2
vt1 2 -> 169.254.200.2
vip 169.254.100.1 and 169.254.200.1
fw2:
vti 1 -> 169.254.100.3
vti2 -> 169.254.200.3
vip 169.254.100.1 and 200.1 (same as fw1)
overlay ID:
same settings, except, in sase portal, you would use for tunnel 1 sase IP as 169.254.100.254 and local ip as 169.254.100.1 (200.254 and 200.1 for tunnel 2)
If using loopback interface method, then you would use say 169.254.241.1 and say .254 for sase for tunnel 1 and then say 240.1 and 240.354 for tunnel 2 (like what I had in the document)
Now, here is the catch. If using OVERLAY id method, tunnels will show as PERMANENT from sase, but not from Check Point, which is not a big deal, as BGP is exchanged and its constantly checking the loopback ip anyway. Plus, they are set as permanent tunnels in community, just show as regular in sv monitor. if you use loopback interface method, they show as permanent.
Difference is, if using overlay ID, then tunnel is terminated on tunnel interface, rather than loopback one.
This is somewhat similar for Forti SASE (Fortinet solution), Prisma (PAN sase) and Aruba Axis is definitely more simple setup, as it uses connectors method. I assume its same for Cisco Connect, but since I had never seen it, cant really say 🙂
If anything else comes to mind and we end up testing, will update.
Best,
Andy
Something important to consider...if you are doing BGP through the tunnel, here is the key. So router id can be say 169.254.241.1 (like our lab) and then you create 2 peers say with IP 169.254.240.254 and 169.254.241.254, as it would let you use it as such for redundant tunnels. I attached what I mean.
Andy
Also, overlay can be used instead of loopback, so say if router ID is 169.254.241.1, peers can be say 169.254.100.254 and 200.254, that works fine. For some reason, though tunnels are up, on CP side they dont show as permanent, just regular, so we will look into it.
Andy
Hey guys,
Wanted to update with something else my colleague and I discovered. So, I will give an example we used and this is with numbered vti's, since we did not want to spend too much time with troubleshooting why unnumbered did not work, plus we are not even sure its supported 🙂
Example for redundant tunnels (you need advanced license to do this, since basic one only allows for single tunnels for 1 POP, not 2 or more). Btw, since sd-wan is not supported with this yet, then load balancing the traffic among the multiple ISP links is not really an option, but from what we tested, all else seems to work fine.
loopback interface:
router ID 169.254.241.1
local as 65000
remote as 65001
peer 1 -> 169.254.100.254
peer 2 -> 169.254.200.254
fw1:
vti 1 -> 169.254.100.2
vt1 2 -> 169.254.200.2
vip 169.254.100.1 and 169.254.200.1
fw2:
vti 1 -> 169.254.100.3
vti2 -> 169.254.200.3
vip 169.254.100.1 and 200.1 (same as fw1)
overlay ID:
same settings, except, in sase portal, you would use for tunnel 1 sase IP as 169.254.100.254 and local ip as 169.254.100.1 (200.254 and 200.1 for tunnel 2)
If using loopback interface method, then you would use say 169.254.241.1 and say .254 for sase for tunnel 1 and then say 240.1 and 240.354 for tunnel 2 (like what I had in the document)
Now, here is the catch. If using OVERLAY id method, tunnels will show as PERMANENT from sase, but not from Check Point, which is not a big deal, as BGP is exchanged and its constantly checking the loopback ip anyway. Plus, they are set as permanent tunnels in community, just show as regular in sv monitor. if you use loopback interface method, they show as permanent.
Difference is, if using overlay ID, then tunnel is terminated on tunnel interface, rather than loopback one.
This is somewhat similar for Forti SASE (Fortinet solution), Prisma (PAN sase) and Aruba Axis is definitely more simple setup, as it uses connectors method. I assume its same for Cisco Connect, but since I had never seen it, cant really say 🙂
If anything else comes to mind and we end up testing, will update.
Best,
Andy
Another quick update...failover works well, we also tested "downing" both ISPs (one at a time of course : - ) and that went fine as well. P81 agent was able to access all it was supposed to.
Andy
Leaderboard
Epsum factorial non deposit quid pro quo hic escorol.
| User | Count |
|---|---|
| 1 | |
| 1 | |
| 1 | |
| 1 |
Tue 24 Nov 2026 @ 01:30 PM (GMT)
La nueva realidad de los ataques DDoS: autonomía, escala y el futuro de la defensaWed 02 Dec 2026 @ 03:30 PM (GMT)
The New DDoS Reality: Autonomy, Scale, and the Future of DefenseTue 24 Nov 2026 @ 01:30 PM (GMT)
La nueva realidad de los ataques DDoS: autonomía, escala y el futuro de la defensaWed 02 Dec 2026 @ 03:30 PM (GMT)
The New DDoS Reality: Autonomy, Scale, and the Future of DefenseAbout CheckMates
Learn Check Point
Advanced Learning
WE SECURE YOUR AI TRANSFORMATION