- CheckMates
- :
- Products
- :
- Quantum
- :
- Management
- :
- Re: Manual on how to disassemble management server...
Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
Are you a member of CheckMates?
×
Sign in with your Check Point UserCenter/PartnerMap account to access more great content and get a chance to win some Apple AirPods! If you don't have an account, create one now for free!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Manual on how to disassemble management server smart-1 225?
I would be needing some kind of a manual on how to disassemble smart-1 225 server, our server failed, we got the replacement server and was told by support to swap out all drives,ram,modules with the new server, so will need some kind of a manual that explains how to do so. In the meantime this is what I found-
Is this PDF enough for my purpose?
Thanks and Regards.
10 Replies
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
All the documentation should be linked here: https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solut...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
thank you as always
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
also when attaching that band to my wrist do you know where do i have to attach that band to for grounding as is shown in the images?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
If I recall correctly, attaching it to the metal case of the appliance is sufficient.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you as always!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
So I tried to replace both hard drives, ram, and tried turning on the new server but it does not boot up and gives out this beeping sound continuously, why does that happen?I made sure to seat the rams and hard drives properly, what else should I do to make it boot up?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
do i have to swap out the power supply units as well? is that why its not booting? becauase im still using the old power cables on the new server (they didnt send any cables,manuals etc in the box, all they sent was the server itself).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
If the system powers up at all, the power supply is probably fine.
I would engage with the TAC here.
I would engage with the TAC here.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
So it turns out my ram was loosely connected (somehow you need to apply a lot of force to insert them properly) that is why it was beeping but then I made sure to properly place the ram, so I thought that would fix the issue for sure, bit it still stays stuck at initialising, no beep now but yeah still stuck, so yeah I am engaging with tac now.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Connect to the Ground contacts of e.g. the power strip on your desk.
CCSP - CCSE / CCTE / CTPS / CCME / CCSM Elite / SMB Specialist
