Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
HeikoAnkenbrand
Champion Champion
Champion

R80.x - Performance Tuning Tip - Management Data Plane Separation

Management Data Plane Separation allows a security gateway to have isolated management and data networks. The network system of each domain (plane) is independent and includes interfaces, routes, sockets, and processes. This has the performance advantage that some processes run separately from the firewall core daemon. Thus it reduces the load on the firewall processes, e.g. during the policy installation.

The management plane is a domain whose purpose is to access, provision, and monitor the gateway. This includes:
      - Routing separation
      - Resource Separation
                 - Access:                         SSH, FTP, and more
                 - Provisioning:               Policy installation, GAIA Portal, RestAPI's, and more
                 - Monitoring:                  Logs, SNMP, and more

When resource separation is enabled, the security gateway will separat the management instance. Here is an example:

Mgmt
instance

CPU core 0

SND


CPU core 1

SND


CPU core 2

CoreXL
instance

CPU core 3

CoreXL
instance

CPU core 4

CoreXL
instance

CPU core 5

CoreXL
instance

CPU core 6

CoreXL
instance

CPU core 7


This feature can be enabled with the following minimum requirements:
      - R80.30 kernel 3.10 and JHF 136 or higher
      - R80.20SP JHF 194 or higher
      - To enable this option, at least 4 cores and 3 CoreXL FW instances are required.


TIP 1

To configure Management Data Plane Separation or if you need more information take a look at this SK138672.

TIP 2
This can also help if a gateway or a ClusterXL member goes into CUL freeze mode (SK92723) during policy installation through high CPU load on cluster member or single gateway.

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips
20 Replies
m_oeqvist
Explorer

Is this also possible with R80.10 or R80.20 and the latest JHF?

HeikoAnkenbrand
Champion Champion
Champion

Unfortunately not.

➜ CCSM Elite, CCME, CCTE ➜ www.checkpoint.tips
_Val_
Admin
Admin

3.10 kernel is required for that functionality, so no

0 Kudos
spiros-p
Participant

We use this with R80.30 and kernel 3.10.
Since we have been using it we have no problems with high CPU usage when installing policies.

charlie_h
Participant

Does this not reduce a core license?

0 Kudos
Andreas_Aust
Collaborator

One has to die one death

0 Kudos
osef
Contributor

In sk138672, we can found this :

Setting the 'sync' interface. When you use Routing Separation and ClusterXL, you must set the Sync interface on the Management Plane. The interface is used for ClusterXL synchronization between members.

and this :

The use of logical interfaces is not supported on management interface (Alias, Bridge, VPN Tunnel, 6in4 Tunnel, PPPoE, Bond, VLAN)

 

So, if I understand correctly,

- It's mandatory to put the sync interface in the management plane

- Management plane doesn't support bonding

 

So if my sync interface is a bond, I can't use management place, correct ?

(2)
_Val_
Admin
Admin

You need MGMT plane separation when your machine is extremely busy with FW operations. we are talking 90+% average CPU utilization. That is the only use case. 

0 Kudos
(1)
osef
Contributor

Thanks for the answer but if I understand correctly, this feature also allow "routing" and "ressources" separation, right ?

So I can put the management interface into a separate "VRF" and if I shoot myself in the foot with the routing, the management server will still be able to reach the gateways through the management interface. 

Do I understand this correctly?

0 Kudos
_Val_
Admin
Admin

No, that interpretation is not correct. Routing here means traffic filtering and forwarding. As kernel related CPU tasks usually have highest priority, MGMT plane allows taking one CPU for processes only hence allowing logging, admin processes and WebUI access unaffected, if FW tasks are taking too much CPU time

0 Kudos
osef
Contributor

Sorry but I'm extremly confused now 😅

In sk138672, we can read this : 
(a) Routing Separation
Routing Separation creates a routing domain (ID 1) that includes an interface that the Gateway uses to communicate with Management, and an interface used for the synchronization of cluster members (when using ClusterXL). This domain has its own routing table, in which routing decisions are made. It is not connected with the Data Plane via any virtual adapter. This means that any packet that is inbound to the Gateway, whether on the Management or on the Data Plane, cannot cross over to the other plane.

 

So if I'm reading this correctly, it's like a VRF, no ?

_Val_
Admin
Admin

Sorry, my bad, I misread your original comment. 

Yes, there is a different routing domain for management only communications. I think VRF terms are no longer applicable on 3.10, but I cannot recall the new name other than routing domain, sorry 🙂

0 Kudos
osef
Contributor

Okay 🙂

So for my original question, if my sync interface is a bonding, I can't use the "routing separation", correct ?

0 Kudos
_Val_
Admin
Admin

Bonding is not supported with MGMT plane, you answered this yourself.

0 Kudos
osef
Contributor

I wanted to be sure 😞

I think it's a very big limitation and it's going to prevent the deployment of this feature where it's the most needed 😞 If Checkpoint could remove this limitation, it would be great !

Power_Support
Participant

Are there plans for bonding to be supported in the future?

_Val_
Admin
Admin

The support limitations are coming from RH side. It is not possible with 3.10 kernel to get bonding working on MGMT plane. Also, it kinda productive, as MGMT interface should not carry any production traffic.

0 Kudos
osef
Contributor

But it's a requirement to put the sync interface in the MGMT plane and bonding on the sync interace is a must for high availability. I realy hope checkpoint will remove this limitation one day

_Val_
Admin
Admin

I see your point.

0 Kudos
M_Ruszkowski
Collaborator

The issue that we are having with this new feature is the way CP implemented it when it comes to SNMP.   Switching the gateways to mplane was great for routing, but it had a side effect and broke a lot of out monitoring tools.  Without going into too many details, in order to get all the monitoring data needed such as interfaces, cpu. memory, you have to use the context argument "-n dplane" for SNMPv3.  Not all the tools support this.   We expect when we connect to a device via SNMP we should get all the data; basically everything we need to monitor.  I am not sure how all other Network Vendors are implementing their dedicated Mgmt interfaces, but I guess I really don't care, as long as it acts seemless to the user and all of our tools.  It feels like CP did not put a lot of thought into the way this feature was implemented.

Leaderboard

Epsum factorial non deposit quid pro quo hic escorol.

Upcoming Events

    CheckMates Events