- Products
- Learn
- Local User Groups
- Partners
- More
What’s New in Device Diagnostics?
Dec 2nd @ 5pm CET / 11am EST
AI Security Masters
Security in the Pace of AI:
From Threat to Force Multiplier
CPX is Back!
Join us in Las Vegas, Vienna, and/or Bangkok!
Check Point Named a Leader
The Forrester Wave:
Enterprise Firewall Solutions, Q4 2026
What’s New in Agentic Network Orchestration
CheckMates Go:
Fun Ding
Hi,
just tried to implement idrac on a new Smart-1. We did that already on an other device successfully.
Are there any more troubleshooting commands available than mentioned in sk122914? No FTW done yet.
Basically, what does Error:iDRAC access denied mean exactly?
Is no IDRAC card inserted?
[Expert@SMART-1:0]# SetiDRACUser
Enter User ID: 6
Enter User name: <ADMIN>
Enter Password:
Enter Password again:
Please Wait, Updating User..
Error:iDRAC access denied
Error:iDRAC access denied
New iDRAC user added successfully
lomipset 10.x.x.x 255.255.255.0 10.x.x.x has been done
[Expert@SMART-1:0]> show lom
Firmware Revision : 4.40
IP Address : 0.0.0.0
more cp_idrac.log
Starting: Set iDRAC User
[09/19/22@09:10:33]:in idrac_set_user_password_enforce user=<ADMIN>
[09/19/22@09:10:33]:in idrac_set_user_password user=<ADMIN>
[09/19/22@09:10:34]:in idrac_set_user_password user_id = 6 user=<ADMIN>
[09/19/22@09:10:34]:idrac_exec_cmd_over_ssh:sshpass_cmd=#/bin/sshpass -e /bin/ss
h -q -o StrictHostKeyChecking=no -o ServerAliveInterval=1 [email protected] raca
dm set iDRAC.Users.6.Privilege 0x171#
[09/19/22@09:10:34]:in idrac_setup_usbnic
[09/19/22@09:10:39]:Error:failed to read to iDRAC cmd output
[09/19/22@09:10:39]:Error:iDRAC access denied
[09/19/22@09:10:39]:idrac_exec_cmd_over_ssh:sshpass_cmd=#/bin/sshpass -e /bin/ss
h -q -o StrictHostKeyChecking=no -o ServerAliveInterval=1 [email protected] raca
dm set iDRAC.Users.6.Enable 1#
[09/19/22@09:10:39]:in idrac_setup_usbnic
[09/19/22@09:10:44]:Error:failed to read to iDRAC cmd output
[09/19/22@09:10:44]:Error:iDRAC access denied
[09/19/22@09:12:20]:idrac_exec_cmd_over_ssh:sshpass_cmd=#/bin/sshpass -e /bin/ss
h -q -o StrictHostKeyChecking=no -o ServerAliveInterval=1 [email protected] raca
dm get iDRAC.IPv6.Enable#
[09/19/22@09:12:20]:in idrac_setup_usbnic
[09/19/22@09:12:25]:Error:failed to read to iDRAC cmd output
[09/19/22@09:12:25]:Error:iDRAC access denied
[09/19/22@09:12:25]:idrac_exec_cmd_over_ssh:sshpass_cmd=#/bin/sshpass -e /bin/ss
h -q -o StrictHostKeyChecking=no -o ServerAliveInterval=1 [email protected] raca
dm getniccfg#
[09/19/22@09:12:25]:in idrac_setup_usbnic
[09/19/22@09:12:30]:Error:failed to read to iDRAC cmd output
[09/19/22@09:12:30]:Error:iDRAC access denied
Thanks
Regards
just as an update. Could get manage to setup idrac on all devices.
After update LOM firmware to 5.10 AND establish connectivity to the LOM port, the error message
09/19/22@09:10:39]:Error:failed to read to iDRAC cmd output
[09/19/22@09:10:39]:Error:iDRAC access denied
disappeared.
And LOM update does only work when your device has already IP connectivity via any other port (MGMT,access)
Thanks, Regards
What precise model is it?
On the other Smart-1 appliances, did you do it before or after first time wizard was executed?
hi
same model on 2 locations: Smart-1 6000-L
No FTW until now. Just preparation work before migration stuff.
Regards
sk176942: iDRAC Troubleshooting might assist, if there are still issues I advise to open ticket with our support.
Hi,
did not see the SK176942 before. Thanks a lot
However, still get the same message. I will open a TAC case
Regards
[Expert@SMART-1:0]# cpidrac --get_external_nic_state
Error:iDRAC access denied
[Expert@SMART-1:0]# service ipmi status
ipmi_msghandler module loaded.
ipmi_si module loaded.
ipmi_devintf module loaded.
/dev/ipmi0 exists.
cat /config/active | grep -i idrc
interface:eth-idrc0:state on
interface:eth-idrc0:ipaddr:169.254.0.2:mask 24
just as an update. Could get manage to setup idrac on all devices.
After update LOM firmware to 5.10 AND establish connectivity to the LOM port, the error message
09/19/22@09:10:39]:Error:failed to read to iDRAC cmd output
[09/19/22@09:10:39]:Error:iDRAC access denied
disappeared.
And LOM update does only work when your device has already IP connectivity via any other port (MGMT,access)
Thanks, Regards
Leaderboard
Epsum factorial non deposit quid pro quo hic escorol.
| User | Count |
|---|---|
| 30 | |
| 8 | |
| 7 | |
| 5 | |
| 5 | |
| 4 | |
| 4 | |
| 4 | |
| 4 | |
| 3 |
Tue 24 Nov 2026 @ 01:30 PM (GMT)
La nueva realidad de los ataques DDoS: autonomía, escala y el futuro de la defensaWed 02 Dec 2026 @ 03:30 PM (GMT)
The New DDoS Reality: Autonomy, Scale, and the Future of DefenseThu 03 Dec 2026 @ 11:00 AM (EST)
Under the Hood: Check Point Cloud Firewall for Nutanix - How to Secure your AI WorkloadsTue 24 Nov 2026 @ 01:30 PM (GMT)
La nueva realidad de los ataques DDoS: autonomía, escala y el futuro de la defensaWed 02 Dec 2026 @ 03:30 PM (GMT)
The New DDoS Reality: Autonomy, Scale, and the Future of DefenseThu 03 Dec 2026 @ 11:00 AM (EST)
Under the Hood: Check Point Cloud Firewall for Nutanix - How to Secure your AI WorkloadsAbout CheckMates
Learn Check Point
Advanced Learning
WE SECURE YOUR AI TRANSFORMATION