SMB GWs Advanced Settings

[G_W_Albrecht]

In Device > Advanced > Advanced Settings you can manage very advanced settings of the device. This is very important for locally managed units as they have no .def files on SMS for advanced configuration.

Changing these Advanced Settings can be harmful to the stability, security and performance of the appliance, so they should only be used in special configurations and when advised by CP – the default settings are suggested for best performance and security. As an example, FW Rulebase can only Accept or Block packets – when set to Block, traffic from external is dropped, from internal rejected. This behaviour can be changed on locally managed devices using the "Firewall Policy - Blocked packets action" parameter.

The following list contains all Advanced Settings included in firmware R77.20.85. Although you can search and read them in Embedded GAiA WebGUI, i sometimes find it more convenient to have a complete list .

The Advanced Settings on centrally managed units contain only 18 parameters:

Attribute Name	Type	Value	Description
Additional Management Settings - Move temporary policy files to storage	bool	false	Indicates whether the temporary policy installation files will be saved to the storage partition
Anti ARP Spoofing - Anti ARP Spoofing mode	options	Off	Mode for Anti ARP spoofing protection. The protection can be turned off, on or in detect only mode
Anti ARP Spoofing - Detection window time to indicate attack	int	180	Time period (in seconds) during which IP addresses, assigned to the same MAC address, indicate an ARP spoofing attack
Anti ARP Spoofing - Number of IP addresses to indicate attack	int	3	The number of IP addresses assigned to the same MAC address during the Detection window time that will indicate an ARP spoofing attack
Anti ARP Spoofing - Suspicious MAC block period	int	1800	Time period (in seconds) during which suspicious MAC addresses are kept in the blocked list
MAC Filtering settings - Log blocked MAC addresses	options	Enabled	Indicates if blocked MAC addresses should be logged or not
MAC Filtering settings - Log suspension	int	1	Indicates the suspension time (in seconds) between logs for blocked MAC addresses
Internet - Reset Sierra USB on LSI error	bool	true	Indicates whether Sierra type USB modems will be reset when they send an Invalid LSI signal
DHCP relay - Use internal IP addresses as source	bool	false	Indicates if DHCP relay packets from the appliance will originate from internal IP addresses
Serial port - Port speed	options	115200	Indicates the port speed (Baud Rate) of the serial connection
Serial port - Flow control	options	RTS/CTS	Indicates the method of data flow control to and from the serial port
Serial port - Enable serial port	options	Enabled	Indicates if the serial port is enabled
Serial port - Mode	options	Console	Indicates if the serial port is used to connect to the appliance's console, a remote telnet server or allow a remote telnet connection to the device connected to the serial port.
Hotspot - Enable portal	options	Enabled	Select 'Disabled' to disable the hotspot feature entirely
USB modem watchdog - Interval	int	5	Indicates how often the USB modem watchdog probes the internet
USB modem watchdog - Mode	options	Disabled	Indicates if the USB modem watchdog is enabled when internet probing is enabled, and the reset type (either hard-reset to shut down the power for the USB modem or gateway-reset to reboot the gateway itself).
Hotspot - Prevent simultaneous log-in	bool	false	The same user will not be allowed to login via hotspot portal from more than one machine in parallel
Report Settings - Max Period	options	Weekly	Maximum period to collect and monitor data. You must reboot your appliance to apply changes.

Advanced Settings on StandAlone units contain 256 parameters (sorted alphabetically):

Attribute Name	Type	Value		Description
Admin Lockout - Mobile application session timeout	int	30		Allowed mobile application session before automatic logout is executed (in days)
Administrators RADIUS authentication - Local authentication (RADIUS inaccessible)	bool	false		Perform local administrator authentication only if RADIUS server is not configured or is inaccessible.
Aggressive aging - Aggressive aging enforcement method	options	Both		Choose when aggressive aging timeouts are enforced
Aggressive aging - Connection table percentage limit	int	80		Connection table percentage limit
Aggressive aging - Enable aggressive aging of connections	bool	true		Enable aggressive aging of connections
Aggressive aging - Enable reduced timeout for ICMP connections	bool	true		Enable reduced timeout for ICMP connections
Aggressive aging - Enable reduced timeout for non TCP/UDP/ICMP connections	bool	false		Enable reduced timeout for non TCP/UDP/ICMP connections
Aggressive aging - Enable reduced timeout for TCP handshake	bool	true		Enable reduced timeout for TCP handshake
Aggressive aging - Enable reduced timeout for TCP session	bool	true		Enable reduced timeout for TCP session
Aggressive aging - Enable reduced timeout for TCP termination	bool	true		Enable reduced timeout for TCP termination
Aggressive aging - Enable reduced timeout for UDP connections	bool	true		Enable reduced timeout for UDP connections
Aggressive aging - ICMP connections reduced timeout	int	3		ICMP connections reduced timeout
Aggressive aging - Memory consumption percentage limit	int	80		Memory consumption percentage limit
Aggressive aging - Other IP protocols reduced timeout	int	15		Other IP protocols reduced timeout
Aggressive aging - Pending Data connections reduced timeout	int	15		Pending Data connections reduced timeout
Aggressive aging - TCP handshake reduced timeout	int	5		TCP handshake reduced timeout
Aggressive aging - TCP session reduced timeout	int	600		TCP session reduced timeout
Aggressive aging - TCP termination reduced timeout	int	3		TCP termination reduced timeout
Aggressive aging - Tracking options for aggressive aging	options	Log		Tracking options for aggressive aging
Aggressive aging - UDP connections reduced timeout	int	15		UDP connections reduced timeout
Anti ARP Spoofing - Anti ARP Spoofing mode	options	Off		Mode for Anti ARP spoofing protection. The protection can be turned off, on or in detect only mode
Anti ARP Spoofing - Detection window time to indicate attack	int	180		Time period (in seconds) during which IP addresses, assigned to the same MAC address, indicate an ARP spoofing attack
Anti ARP Spoofing - Number of IP addresses to indicate attack	int	3		The number of IP addresses assigned to the same MAC address during the Detection window time that will indicate an ARP spoofing attack
Anti ARP Spoofing - Suspicious MAC block period	int	1800		Time period (in seconds) during which suspicious MAC addresses are kept in the blocked list
Anti-Spam policy - All mail track	options	None		Indicates the tracking options for non-spam emails
Anti-Spam policy - Allowed mail track	options	None		Indicates the tracking options for emails that were explicitly allowed in the Exceptions page
Anti-Spam policy - Bypass timeout	int	0		Indicates the timeout (in seconds) of a POP3 inspection bypass mechanism. Bypass will be activated in case the inspection daemon is unavailable for the indicated time period. Relevant for POP3 and for Anti-Virus, Anti-Spam and Threat Emulation inspection. A value of zero means bypass is disabled.
Anti-Spam policy - Content based Anti-Spam timeout	int	10		Indicates the timeout (in seconds) to wait for an answer from the cloud during content-based Anti-Spam inspection
Anti-Spam policy - E-mail size scan	int	8		Indicates the maximal size of an email's content to scan (in KB)
Anti-Spam policy - IP reputation fail open	bool	true		Use Anti-Spam IP reputation fail-open mode upon internal error
Anti-Spam policy - IP reputation timeout	int	10		Indicates the timeout (in seconds) to wait for an IP reputation test result
Anti-Spam policy - Scan outgoing emails	bool	false		Scan the content of emails which are sent from the local network to the Internet
Anti-Spam policy - Transparent proxy	bool	true		Use a transparent proxy for inspected email connections
Anti-spoofing - Enable global anti-spoofing	bool	true		Indicates if anti-spoofing is enabled automatically on all interfaces according to their zone
Application Control and URL Filtering - Block when service is unavailable	bool	false		Block web requests traffic when the Check Point categorization and widget definitions  web service is unavailable
Application Control and URL Filtering - Categorize cached and translated pages	bool	true		Perform URL categorization of cached pages and translated pages created by search engines
Application Control and URL Filtering - Custom App over HTTPS	bool	false		Indicates whether custom URLs and applications will be matched over HTTPS traffic using SNI field. Important note: as SNI field in HTTPS traffic is browser-dependent and promiscuous, it does not guarantee 100% match.
Application Control and URL Filtering - Enforce safe search	bool	false		Force filtering explicit content in search engines results
Application Control and URL Filtering - Fail Mode	options	Block all requests		Indicates the action to take on traffic in case of an internal system error or overload
Application Control and URL Filtering - Track browse time	bool	true		Indicates if the total time that users are connected to different sites and applications in an HTTP session will be shown in relevant logs
Application Control and URL Filtering - Use HTTP referer header	bool	true		Indicates if the HTTP referer header is used by the inspection engine to improve application identification
Application Control and URL Filtering - Web site categorization mode	options	Background		Indicates the categorization mode: Background - requests are allowed until categorization is complete, Hold - requests are blocked until categorization is complete
Capacity Optimization - Connections hash table size	int	131072		Indicates the size in bytes of the connections hash table
Capacity Optimization - Maximum concurrent connections	int	150000		Indicates the overall maximum number of concurrent connections
Cloud Services firmware upgrade - Service access maximum retries	int	3		Indicates the maximum number of retries when failing to upgrade using the service
Cloud Services firmware upgrade - Service access timeout until retry	int	180		Indicates the time to wait when a connection failure to the service before the next retry
Cluster - Use virtual MAC	bool	false		Indicates if a virtual MAC address will be used by all cluster members to allow a quicker failover by the network's switch
DDNS - iterations	int	1		Number of DNS updates
DHCP relay - Use internal IP addresses as source	bool	false		Indicates if DHCP relay packets from the appliance will originate from internal IP addresses
Firewall Policy - Blocked packets action	options	Automatic		Action for blocked packets: Drop, reject or automatic (drop from external and reject from internal)
Firewall Policy - Log implied rules	bool	false		Produce log records for connections that match implied rules
General temporary directory size - General temporary directory size	int	20		Controls the size (in MB) of the general temporary directory
General temporary directory size - System temporary directory size	int	40		Controls the size (in MB) of the temporary directory that is used by the system
Hardware options - Reset to factory defaults timeout	int	12		Indicates the amount of time (in seconds) that you need to press and hold the factory defaults button on the back panel to restore to the factory defaults image
Hotspot - Enable portal	options	Enabled		Select 'Disabled' to disable the hotspot feature entirely
Hotspot - Prevent simultaneous log-in	bool	false		The same user will not be allowed to login via hotspot portal from more than one machine in parallel
Internal Certificates configure - Internal CA certificate expiration	int	20		The number of years the internal CA certificate is valid
Internet - Reset Sierra USB on LSI error	bool	true		Indicates whether Sierra type USB modems will be reset when they send an Invalid LSI signal
IP fragments parameters - Action	options	Allow		Indicates if IP fragments will be allowed or dropped by default
IP fragments parameters - Maximum fragments	int	200		Indicates how many IP fragments can arrive before discarding incomplete packets
IP fragments parameters - Minimum fragments size	int	0		IP Fragments minimum fragment size
IP fragments parameters - Packet Capture	bool	false		IP Fragments packet capture settings
IP fragments parameters - Timeout	int	1		Indicates the timeout (in seconds) before discarding incomplete packets
IP fragments parameters - Track options	options	Log		Indicates if and how to log IP fragments
IPS additional parameters - Max Ping Limit	int	1000		Indicates the maximal ping packet size that will be allowed when the 'Max Ping Size' protection is active
IPS additional parameters - Non-standard HTTP ports	bool	true		Enable HTTP inspection on non-standard ports for the IPS blade
IPS engine settings - Description	comments	Access denied due to IPS policy violation		A configured string to show in the error page if configured
IPS engine settings - Error page for supported web protections	options	Show pre-defined HTML error page		Indicates if IPS protections supporting an error page will show it upon attack prevention
IPS engine settings - HTML error page configuration	bool	false		Indicates if the error page will contain an error code
IPS engine settings - Logo URL	bool	false		Optionally enter a URL that leads to your company logo.
IPS engine settings - Logo URL address	url			An accessible URL that leads to a logo file to show in the error page
IPS engine settings - Send detailed error code	bool	true		indicates if the error page will contain a configured string
IPS engine settings - Send error code	bool	false		Indicates if an error code will be sent to the other URL as a parameter
IPS engine settings - URL for redirection	url			Users will be redirected to this URL upon detection of an attack
MAC Filtering settings - Log blocked MAC addresses	options	Enabled		Indicates if blocked MAC addresses should be logged or not
MAC Filtering settings - Log suspension	int	1		Indicates the suspension time (in seconds) between logs for blocked MAC addresses
Managed services - Allow seamless administrator access from remote Management Server	bool	true		Indicates if an administrator can access the appliance from a remote Security Management Server without the need to enter an administrator user name and password
Managed services - Show device details in Login	bool	true		Indicates if appliance details are shown when an administrator accesses the appliance
Mobile Settings - Include administrator name in the pairing URL	bool	false		Include administrator name in the pairing URL (less secured)
Mobile Settings - Include gateway name in the pairing URL	bool	false		Include gateway name in the pairing URL (less secured)
Mobile Settings - Notification cloud server URL	urlv6	https://smbcloud-dev-api-gateway.kube1.iaas.checkpoint.com/fcm/send		Cloud server URL used for sending mobile notificatoin
Mobile Settings - Pairing code expiration	int	1		Time till pairing code is expired
Mobile Settings - Verify SSL certificate	bool	true		Verify SSL certificate when sending mobile notification to cloud server
NAT - Address allocation and release tracking	options	None		Specifies whether to log each allocation and release of an IP address from the IP Pool
NAT - Address exhaustion tracking	options	Log		Indicates whether or not to log and/or alert on exhaustion of IP pool
NAT - ARP manual file merge	bool	false		Indicates, when automatic ARP detection is enabled, to use the ARP definitions in a local file with higher priority
NAT - Automatic ARP detection	bool	true		Automatically detect ARP requests for external IP addresses of internal devices to be answered by the device
NAT - Increase hide capacity	bool	true		Indicates if hide-NAT capacity is given additional space
NAT - IP Pool NAT	options	Do not use IP pool NAT		IP pool NAT mode
NAT - IP pool per interface	bool	false		Uses an IP address pool for NAT per interface
NAT - NAT cache expiration	int	30		Indicates the expiration time in minutes for NAT cache entries
NAT - NAT cache number of entries	int	10000		Indicates the maximum number of NAT cache entries
NAT - NAT enable	bool	true		Indicates if the device's NAT capabilities are enabled
NAT - NAT hash size	int	0		Indicates the hash bucket size of NAT tables
NAT - NAT limit	int	0		Indicates the maximum number of connections with NAT
NAT - Perform cluster hide fold	bool	false		Indicates if local IP addresses will be hidden behind the cluster IP address when applicable
NAT - Prefer IP Pool NAT over hide NAT	bool	true		Overrides hide NAT with IP pool NAT
NAT - Return unused addresses to IP Pool NAT after x minutes	int	60		Return unused addresses to IP pool NAT
NAT - Reuse IP addresses from the Pool for different destinations	bool	false		Allows NAT to re-use IP addresses for different destinations
NAT - Translate destination on client side	bool	true		Translates destination IP addresses on client side (for automatically generated NAT rules)
NAT - Translate destination on client side (manual rules)	bool	true		Translates destination IP addresses on client side (for manually configured NAT rules)
NAT - Use IP Pool NAT for gateway to gateway connections	bool	false		Uses IP pool NAT for gateway to gateway connections
NAT - Use IP Pool NAT for VPN clients connections	bool	false		Uses IP Pool NAT for VPN clients connections
Notifications policy - Send push notifications	bool	true		Indicates whether notifications are sent to mobile application
Notifications policy - The maximum number of notifications sent to mobile devices per hour	int	60		The maximum number of notifications sent to mobile devices per hour
Privacy settings - Help us improve product experience by sending data to Check Point	bool	true		Privacy statement: Check Point does not upload data that contains private or sensitive information. For more information, refer to sk120332.
QoS blade - Logging	bool	true		Indicates if the appliance logs QoS events when the QoS blade is enabled
Reach My Device - Ignore SSL certificate	bool	false		Ignore SSL certificate when running Reach My Device
Reach My Device - Server address	url	smbrelay.checkpoint.com		Indicates the address of the remote server that allows administration access to the appliance from the internet even when behind NAT
Report Settings - Max period	options	Monthly		Maximum period to collect and monitor data in local management. You must reboot your appliance to apply changes.
Serial port - Enable serial port	options	Enabled		Indicates if the serial port is enabled
Serial port - Flow control	options	RTS/CTS		Indicates the method of data flow control to and from the serial port
Serial port - Mode	options	Console		Indicates if the serial port is used to connect to the appliance's console, a remote telnet server or allow a remote telnet connection to the device connected to the serial port.
Serial port - Port speed	options	115200		Indicates the port speed (Baud Rate) of the serial connection
SSL inspection policy - Additional HTTPS ports	port-range	8080, 3128		Additional HTTPS ports for ssl inspection (a comma separated list of ports/ranges)
SSL inspection policy - Log empty SSL connections	bool	false		Log connections that were terminated by the client before data was sent - might indicate the client did not install CA certificate
SSL inspection policy - Retrieve intermediate CA certificates	bool	true		Indicates if the SSL inspection mechanism will perform it's validations on all intermidate CA certificates in the certificate chain
SSL inspection policy - SSL Inspection categorization mode	options	Hold		Indicates the categorization mode of SSL Inspection: Background - requests are allowed until categorization is complete, Hold - requests are blocked until categorization is complete
SSL inspection policy - Track validation errors	options	Log		Choose if the SSL Inspection validations are tracked
SSL inspection policy - Validate CRL	bool	true		Indicates if the SSL inspection mechanism will drop connections that present a revoked certificate
SSL inspection policy - Validate Expiration	bool	false		Indicates if the SSL inspection mechanism will drop connections that present an expired certificate
SSL inspection policy - Validate unreachable CRL	bool	false		Indicates if the SSL inspection mechanism will drop connections that present a certificate with an unreachable CRL
SSL inspection policy - Validate untrusted certificates	bool	false		Indicates if the SSL inspection mechanism will drop connections that present an untrusted server certificate
Stateful Inspection - Accept out of state TCP packets	int	0		Indicates if TCP packets which are not consistent with the current state of the TCP connection are dropped (when set to 0) or accepted (when set to any other value)
Stateful Inspection - Accept stateful ICMP Errors	bool	true		Accept ICMP error packets which refer to another non-ICMP connection that was accepted by the Rule Base
Stateful Inspection - Accept stateful ICMP Replies	bool	true		Accept ICMP reply packets for ICMP requests that were accepted by the Rule Base
Stateful Inspection - Accept stateful other IP protocols replies for unknown services	bool	true	Accept stateful non TCP/UDP protocols replies for unknown services
Stateful Inspection - Accept stateful UDP replies for unknown services	bool	true	Accept stateful UDP replies for unknown services
Stateful Inspection - Allow IPv6 packets	bool	false	Allow IPv6 traffic to pass without inspection
Stateful Inspection - Allow LAN-DMZ DPI	bool	true	Allow Deep Packet Inspection in traffic between internal networks and the DMZ network
Stateful Inspection - Allow LAN-LAN DPI	bool	false	Allow Deep Packet Inspection in traffic between internal networks
Stateful Inspection - Drop out of state ICMP packets	bool	true	Drop ICMP packets which are not in the context of a virtual session
Stateful Inspection - ICMP virtual session timeout	int	30	Indicates the timeout (in seconds) for ICMP virtual sessions
Stateful Inspection - Log dropped out of state ICMP packets	int	0	Log dropped out of state ICMP packets
Stateful Inspection - Log dropped out of state TCP packets	int	0	Log dropped out of state TCP packets
Stateful Inspection - Other IP protocols virtual session timeout	int	60	Indicates the timeout (in seconds) for other IP protocols virtual sessions (non TCP/UDP/ICMP)
Stateful Inspection - TCP end timeout	int	20	Indicates the timeout (in seconds) for TCP session end
Stateful Inspection - TCP session timeout	int	3600	Indicates the timeout (in seconds) for TCP sessions
Stateful Inspection - TCP start timeout	int	25	Indicates the timeout (in seconds) for TCP session start
Stateful Inspection - UDP virtual session timeout	int	40	Indicates the timeout (in seconds) for UDP virtual sessions
Stateful Inspection - traceroute maximal TTL	int	29	Maximal value for TTL field for a packet to be considered as a traceroute
Streaming engine settings - Stream Inspection Timeout action	options	Prevent	Stream Inspection Timeout activation mode
Streaming engine settings - Stream Inspection Timeout tracking	options	Log	Stream Inspection Timeout tracking
Streaming engine settings - TCP Invalid Checksum action	options	Prevent	TCP Invalid Checksum activation mode
Streaming engine settings - TCP Invalid Checksum tracking	options	None	TCP Invalid Checksum tracking
Streaming engine settings - TCP Invalid Retransmission action	options	Prevent	TCP Invalid Retransmission activation mode
Streaming engine settings - TCP Invalid Retransmission tracking	options	Log	TCP Invalid Retransmission tracking
Streaming engine settings - TCP Out of Sequence action	options	Prevent	TCP Out of Sequence activation mode
Streaming engine settings - TCP Out of Sequence tracking	options	None	TCP Out of Sequence tracking
Streaming engine settings - TCP Segment Limit Enforcement action	options	Prevent	TCP Segment Limit Enforcement activation mode
Streaming engine settings - TCP Segment Limit Enforcement tracking	options	Log	TCP Segment Limit Enforcement tracking
Streaming engine settings - TCP SYN Modified Retransmission action	options	Prevent	TCP SYN Modified Retransmission activation mode
Streaming engine settings - TCP SYN Modified Retransmission tracking	options	Log	TCP SYN Modified Retransmission tracking
Streaming engine settings - TCP Urgent Data Enforcement action	options	Prevent	TCP Urgent Data Enforcement activation mode
Streaming engine settings - TCP Urgent Data Enforcement tracking	options	Log	TCP Urgent Data Enforcement tracking
Threat Prevention Anti-Bot policy - Resource classification mode	options	Hold	Indicates the classification mode for the Anti-Bot engine: Background - connections are allowed until classification is complete, Hold - connections are blocked until classification is complete
Threat Prevention Anti-Virus policy - File scan size limit	int	0	Indicates the size limit (in KB) of a file scanned by the Anti-Virus engine. To specify no limit, set to 0.
Threat Prevention Anti-Virus policy - MIME maximum nesting level	int	7	Indicates the maximum number of levels in nested MIME content that the ThreatSpect engine scans in mail traffic
Threat Prevention Anti-Virus policy - MIME nesting level exceeded action	options	Block	Indicates if an email should be blocked or accepted if there are more nested levels of MIME content than the configured amount
Threat Prevention Anti-Virus policy - Priority scanning	bool	true	Scan according to security and performance priorities for maximum optimization
Threat Prevention Anti-Virus policy - Resource classification mode	options	Hold	Indicates the classification mode for the Anti-Virus engine: Background - connections are allowed until classification is complete, Hold - connections are blocked until classification is complete
Threat Prevention policy - Block when service is unavailable	bool	false	Block web requests traffic when the Check Point ThreatCloud  web service is unavailable
Threat Prevention policy - Fail mode	options	Allow all requests	Indicates the action to take on traffic in case of an internal system error or overload
Threat Prevention policy - File inspection size limit	int	0	Indicates the size limit (in KB) of a file inspected by Threat Prevention engines. Note: A limit too low may have an impact on the functionality of the Application Control blade. To specify no limit, set to 0.
Threat Prevention policy - Method for skipping HTTP inspection	options	Default	When changed from the default value, and file size inspection limit is used, HTTP inspection will be fully skipped instead of skipping only a single session. This is not recommended due to a high security impact as the following sessions will not be inspected at all following a large file sent via HTTP on a single connection.
Threat Prevention Threat Emulation policy - Emulation connection handling mode - IMAP	options	Background connections are allowed until emulation handling is complete	Indicates the strictness mode of the Threat Emulation engine over IMAP: Background - connections are allowed while the file emulation runs (if needed), Hold - connections are blocked until the file emulation is completed
Threat Prevention Threat Emulation policy - Emulation connection handling mode - POP3	options	Background connections are allowed until emulation handling is complete	Indicates the strictness mode of the Threat Emulation engine over PP3: Background - connections are allowed while the file emulation runs (if needed), Hold - connections are blocked until the file emulation is completed
Threat Prevention Threat Emulation policy - Emulation connection handling mode - SMTP	options	Background connections are allowed until emulation handling is complete	Indicates the strictness mode of the Threat Emulation engine over SMTP: Background - connections are allowed while the file emulation runs (if needed), Hold - connections are blocked until the file emulation is completed
Threat Prevention Threat Emulation policy - Emulation location	options	Emulation is done on Public Threat Cloud	Indicates if emulation is done on Public Threat Cloud or on remote (private) SandBlast
Threat Prevention Threat Emulation policy - Primary Emulation gateway	ipv4addr	Background connections are allowed until emulation handling is complete	The IP address of the primary remote emulation gateway
Update Services Schedule - Maximum number of retries	int	3	Indicates the maximum number of retries for a single update when the cloud is unavailable until the next scheduled update
Update Services Schedule - Timeout until retry	int	180	Indicates the timeout (in seconds) until update retry
USB modem watchdog - Interval	int	5	Indicates how often the USB modem watchdog probes the internet
USB modem watchdog - Mode	options	Disabled	Indicates if the USB modem watchdog is enabled when internet probing is enabled, and the reset type (either hard-reset to shut down the power for the USB modem or gateway-reset to reboot the gateway itself).
USB modem watchdog - USB only	bool	false	Monitor only USB modem connection
User Awareness - Active Directory association timeout	int	720	Indicates the timeout (in minutes) for caching an association between a user and an IP address
User Awareness - Allow DNS for unknown users	bool	true	The default is to allow DNS for unknown users even when configured to be blocked in Browser Based Portal settings
User Awareness - Assume single user per IP address	bool	true	Indicates a mode where per IP address, only the last user who logged is identified
User Awareness - Log blocked unknown users	bool	false	Indicates if a log should be issued when unknown users are blocked (see Browser Based Portal settings)
User Management - Automatically delete expired local users	bool	false	Automatically delete all expired local users every 24 hours (after midnight)
VoIP - Accept MGCP connections to registered ports	bool	false	Indicates if deep inspection over MGCP traffic will automatically accept MGCP connections to registered ports
VoIP - Accept SIP connections to registered ports	bool	false	Indicates if deep inspection over SIP traffic will automatically accept SIP connections to registered ports
VPN Remote Access - Allow clear Traffic while disconnected	bool	true	Indicates how traffic to the VPN domain is handled when the Remote Access VPN client is not connected to the site; sent in clear or dropped
VPN Remote Access - Allow simultaneous login	bool	true	If disabled, and the same user logs in for a second time, it will disconnect his existing session
VPN Remote Access - Authentication timeout	int	120	Indicates for how much time (in minutes) the remote client's password remains valid if timeout is enabled
VPN Remote Access - Authentication timeout enable	bool	false	Indicates if the remote client's password remains valid only for a configured amount of time
VPN Remote Access - Auto-disconnect in VPN domain	bool	true	Indicates if the client disconnects automatically to save resources when it connects from inside the secured internal network (local encryption domain)
VPN Remote Access - Back connections enable	bool	false	Enable back connections from the encryption domain behind the gateway to the client
VPN Remote Access - Back connections keep-alive interval	int	20	Indicates the interval (in seconds) between keep-alive packets to the gateway required for gateway to client back connections
VPN Remote Access - Enable Visitor Mode on All Interfaces	options	All	Enable visitor mode on all interfaces
VPN Remote Access - Enable Visitor Mode on This Interface	ipv4addr	0.0.0.0	Support visitor mode on this interface
VPN Remote Access - Encrypt DNS traffic	bool	true	Indicates if DNS queries sent by the remote client to a DNS server located in the encryption domain are passed through the VPN tunnel
VPN Remote Access - Encryption Method	options	IKEv1	Indicates which IKE encryption method (version) is used for IKE phase 1 and 2
VPN Remote Access - Endpoint Connect re-authentication timeout	int	480	Indicates the time (in minutes) until the Endpoint Connect user's credentials are resent to the gateway to verify authorization
VPN Remote Access - IKE IP Compression Support	bool	false	Indicates if IPSec packets from remote access clients will be compressed
VPN Remote Access - IKE Over TCP	bool	false	Enables support of IKE over TCP
VPN Remote Access - IKE restart recovery	bool	true	Indicates that the gateway will save tunnel details so it can cause the remote client to discard the old SA and re-initiate IKE upon gateway crash or restart
VPN Remote Access - Legacy NAT traversal	bool	true	Indicates if the Check Point proprietary NAT traversal mechanism (UDP encapsulation) is enabled for SecureClient
VPN Remote Access - Minimum TLS version support in the SSL VPN portal	options	TLS 1.2	Indicates the minimum TLS protocol version which the SSL VPN portal supports. For security reasons, it's recommended to support TLS 1.2 and above.
VPN Remote Access - Office Mode allocate from RADIUS	bool	false	Indicates if the Office Mode allocated IP addresses will be taken from the RADIUS server used to authenticate the user
VPN Remote Access - Office Mode disable	bool	false	Indicates if Office Mode (allocating IP addresses for Remote Access clients) is disabled. This is not recommended.
VPN Remote Access - Office Mode Enable With Multiple Interfaces	bool	false	Indicates if a mechanism (with a performance impact) to improve connectivity between remote access client and an appliance with multiple external interfaces is enabled
VPN Remote Access - Office Mode Perform Antispoofing	bool	false	Office Mode - Perform Anti-Spoofing on Office Mode addresses
VPN Remote Access - Prevent IP NAT Pool	bool	false	Prevent IP Pool NAT configuration from being applied to Office Mode users. This is needed when using SecureClient as well as other VPN clients.
VPN Remote Access - Radius retransmit timeout	int	5	Timeout interval (in seconds) for each RADIUS server connection attempt
VPN Remote Access - Remote Access port	port	443	Select the port to which Remote Access clients connect, and SSL VPN Network extender portal uses
VPN Remote Access - Reserve port 443 for port forwarding	bool	false	Reserving port 443 for port forwarding (port 443 will not be used for Remote Access and SSL VPN Network extender)
VPN Remote Access - Single Office Mode Per Site	bool	false	Use first allocated Office Mode IP Address for all connections to the Gateways of the site
VPN Remote Access - SNX keep-alive interval	int	20	Indicates the time (in seconds) between the SSL Network Extender client keep-alive packets
VPN Remote Access - SNX reauthentication timeout	int	480	Indicates the time (in minutes) between re-authentication of SSL Network Extender remote access users and Check Point Mobile VPN users
VPN Remote Access - SNX support 3DES	bool	true	Indicates if the 3DES encryption algorithm will be supported in SSL clients as well as the default algorithms
VPN Remote Access - SNX support RC4	bool	true	Indicates if the RC4 encryption algorithm will be supported in SSL clients as well as the default algorithms
VPN Remote Access - SNX uninstall	options	Do not uninstall	Indicates when and if the SSL Network Extender client will uninstall itself upon disconnection
VPN Remote Access - SNX upgrade	options	Ask user	Indicates when and if the SSL Network Extender client will upgrade itself upon connection
VPN Remote Access - Topology updates manual interval	int	168	Indicates the manually configured interval (in hours) for topology updates to the clients. Will be applicable only if the override settings is set to true.
VPN Remote Access - Topology updates override	bool	false	Indicates if the configured topology updates settings will override the default 'once a week' policy
VPN Remote Access - Topology updates upon startup only	bool	true	Indicates if topology updates will occur only when the client starts. Will be applicable only if the override settings is set to true.
VPN Remote Access - Verify device certificate	bool	true	Client will verify the device's certificate against revocation list
VPN Remote Access - block user if belongs to at least one group without permission	bool	false	Indicates if strict group permissions are enabled - user will not have remote access permission if belongs to at least one group without remote access permission
VPN Site to Site global settings - Accept NAT Traversal	bool	true	Indicates if industry standard NAT traversal (UDP encapsulation) is enabled. This ena- bles VPN tunnel establishment even when the remote site is behind a NAT device.
VPN Site to Site global settings - Administrative notifications	options	Log	Indicates how to log an administrative event (for example, when a certificate is about to expire)
VPN Site to Site global settings - Check validity of IPSec reply packets	bool	false	Check validity of IPSec reply packets
VPN Site to Site global settings - Cluster SA sync packets threshold	long	200000	Sync SA with other cluster members when packets number reaches this threshold
VPN Site to Site global settings - Copy DiffServ mark from encrypted/decrypted IPSec packet	bool	false	Copy DiffServ mark from encrypted/decrypted IPSec packet
VPN Site to Site global settings - Copy DiffServ mark to encrypted/decrypted IPSec packet	bool	true	Copy DiffServ mark to encrypted/decrypted IPSec packet
VPN Site to Site global settings - Delete IKE SAs from a dead peer	bool	true	Delete IKE SAs from a dead peer
VPN Site to Site global settings - Delete IPsec SAs on IKE SA delete	bool	false	Delete IPsec SAs on IKE SA delete
VPN Site to Site global settings - Delete tunnel SAs when Tunnel Test fails	bool	true	When permanent VPN tunnels are enabled and a Tunnel Test fails, delete the relevant peer's tunnel SAs. Not supported in High Availability Cluster mode
VPN Site to Site global settings - Do not encrypt connections originating from the local gateway	bool	false	Exclude the Internet connection's IP address from the local encryption domain. Packets whose original source or destination IP address is the local gateway's Internet connection IP address will not go through a VPN tunnel. This parameter may be useful when the gateway is behind hide NAT.
VPN Site to Site global settings - Do not encrypt local DNS requests	bool	false	When enabled, DNS requests originating from the appliance will not be encrypted. Relevant when a configured DNS server is in a VPN peer's encryption domain.
VPN Site to Site global settings - DPD triggers new IKE negotiation	bool	true	DPD triggers new IKE negotiation
VPN Site to Site global settings - Enable encrypted packets rerouting	bool	true	Indicates if encrypted packets will be rerouted through the best interface according to the peer's IP address or probing. It is not recommended to change this value to false.
VPN Site to Site global settings - Grace period after CRL is no longer valid	int	1800	Indicates the time (in seconds) after which a revoked certificate of a remote site remains valid, to allow wider window for CRL validity in case of clock mismatch
VPN Site to Site global settings - Grace period before CRL is valid	int	7200	Indicates the time window (in seconds) where a certificate is considered valid prior to the time set by the CA, to allow wider window for CRL validity in case of clock mismatch
VPN Site to Site global settings - IKE DoS from known sites protection	options	None	Indicates if the IKE DoS from known IP addresses protection is active and the method by which it detects potential attackers
VPN Site to Site global settings - IKE DoS from unknown sites protection	options	None	Indicates if the IKE DoS from unidentified IP addresses protection is active and the method by which it detects potential attackers
VPN Site to Site global settings - IKE reply from Same IP	bool	true	Indicates if the source IP address used in IKE session will be according to destination when replying to incoming connections, or according to the general source IP address link selection configuration
VPN Site to Site global settings - Join adjacent subnets in IKE Quick Mode	bool	true	Join adjacent subnets in IKE Quick Mode
VPN Site to Site global settings - Keep DF flag on packet	bool	false	Indicates if the 'Don't Fragment' flag is kept on the packet during encryption/decryption
VPN Site to Site global settings - Keep IKE SA Keys	options	Automatic	Keep IKE SA Keys
VPN Site to Site global settings - Key exchange error tracking	options	Log	Indicates how to log VPN configuration errors or key exchange errors
VPN Site to Site global settings - Maximum concurrent IKE negotiations	int	200	Indicates the maximum number of concurrent VPN IKE negotiations
VPN Site to Site global settings - Maximum concurrent tunnels	int	10000	Indicates the maximum number of concurrent VPN tunnels
VPN Site to Site global settings - Open SAs limit	int	20	Indicates the maximum number of open SAs per VPN peer
VPN Site to Site global settings - Outgoing link tracking	options	None	Logging of the outgoing VPN link: Log, don't log or alert
VPN Site to Site global settings - Override 'Route all traffic to remote VPN site' configuration for admin access to the device	bool	true	Exclude admin access traffic to the gateway from being routed to remote VPN site even if all traffic should be routed to it
VPN Site to Site global settings - Packet handling errors tracking	options	Log	Logging for VPN packet handling errors: Log, don't log or alert
VPN Site to Site global settings - Perform Tunnel Tests using an internal IP address	bool	false	Perform Tunnel Tests using an internal IP address which is part of the encryption domain
VPN Site to Site global settings - Permanent tunnel down tracking	options	Log	Logging for when the tunnel goes down: Log, don't log or alert
VPN Site to Site global settings - Permanent tunnel up tracking	options	Log	Logging for when the tunnel goes up: Log, don't log or alert
VPN Site to Site global settings - RDP packet reply timeout	int	10	Timeout (in seconds) for an RDP packet reply
VPN Site to Site global settings - Reply from incoming interface	bool	false	When tunnel is initiated from remote site, reply from the same incoming interface when applicable (IKE and RDP sessions)
VPN Site to Site global settings - Successful key exchange tracking	options	Log	Logging for VPN successful key exchange: Log, don't log or alert
VPN Site to Site global settings - Use cluster IP address for IKE	bool	true	Indicates if IKE is performed using cluster IP address (when applicable)
VPN Site to Site global settings - Use internal IP address for encrypted connections from local gateway	bool	false	Encrypted connections originating from the local gateway will use an internal interface's IP address as the connection source
VPN Site to Site global settings - VPN Tunnel Sharing	options	subnets	Indicates under what conditions new tunnels are created, controlling the number of tunnels: per host pair, per subnet (Industry Standard) or a single tunnel per remote site/gateway
Web Interface Settings and Customizations - Company URL	urlWithHttp		Clicking the company logo in the web interface opens this URL
Web Interface Settings and Customizations - Use a company logo in the appliance's web interface	bool	false	The company logo is displayed on the appliance's web interface and on it´s login page

[G_W_Albrecht]

For more recent versions of Advanced Settings see here:

R81.10.05 Locally Managed Advanced Settings  - & -

New R81.10.05 Locally Managed Advanced Settings

https://community.checkpoint.com/t5/SMB-Gateways-Spark/R80-20-35-Advanced-Settings-changes/m-p/13447...

https://community.checkpoint.com/t5/SMB-Gateways-Spark/R80-20-35-Locally-Managed-Advanced-Settings/m...

https://community.checkpoint.com/t5/SMB-Gateways-Spark/R80-20-25-Locally-Managed-New-Advanced-Settin...

https://community.checkpoint.com/t5/SMB-Gateways-Spark/R80-20-15-Locally-Managed-Advanced-Settings/m...

https://community.checkpoint.com/t5/SMB-Gateways-Spark/R80-20-10-Advanced-Settings/m-p/92079?search-...