SMS Server R80.10 Extremely Slow and Cannot login

[#1]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#2]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#3]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#4]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#5]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#6]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#7]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#8]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#9]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#10]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#11]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#12]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#13]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#14]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[#15]

Hi ,

I'm running R80.10 on my Gateways and SMS Server ( Physical Appliance).  My SMS server was running very slow for same time  and now i cannot even login in Smart Console. Can someone please help troubleshoot/resolve the issue ?

Find in attach the login error, top,sar, iostat and cpview.

SMS SPECS          :  -2 x CPU ; -8 GB RAM ; 

GATEWAY SPECS :  -2 x CPU ( 16 x cores each) ; -32 GB RAM ;

Note: I'm new to checkpoint.

Regards,

Mauro de sousa

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Timothy_Hall · Accepted solution]

You are using a Smart-1 210 which has two cores & 8GB of RAM, yet have manually enabled SmartEvent which is not a supported configuration unless you have 16GB RAM, and that is causing high disk utilization.  See page 15 of the R80.10 release notes; this limitation continues into R80.40 so a software upgrade will not help.  You need to disable SmartEvent on your SMS object in the SmartConsole.  Your peak logging rate is also well in excess of the 210's capacity as specified here: sk112797: Smart-1 R80.x Logging Capacity Performance Improvements.

Even if you upgrade your Smart-1 210 with 16GB of RAM, you will just barely be meeting the minimum requirements for a Mgmt/Log/SmartEvent server, and I doubt you will be satisfied with the performance as your next bottleneck will be CPU.  The Smart-1 210 will reach End of Engineering Support later this year, and all support for that model will terminate in 2022. 

I'd strongly suggest replacing your 210 with a Smart-1 410 which has four cores and 32GB of RAM, concurrent with an management software upgrade to at least R80.30.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[Daniel_Schlifka · Accepted solution]

Timothy is right, you're lacking of hardware resources. You need a bigger box.

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

Thank you very much for your support, now i will try to disable smartevent ( have to find the procedure).

Regards,

Mauro de Sousa

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[Timothy_Hall]

To disable SmartEvent, in the SmartConsole uncheck any boxes under "SmartEvent" on the General Properties...Management screen of your SMS object, then perform an Install Database operation.

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa

[mrl_sousa]

Hi All,

I disable SmartEvent in the begining was slow , but after a restart of SMS, it  started to work nicely but all the Views in "Logs & Monitor" desapeared ( the only one left was "open log View"). So i Re-enable "SmartEvent" and every thing start working nicely ( a lot faster than before) . Now the CPU consumption varies between 7%-100% but always "Up-Down"  and does not stay for more than 3s in 100% . Also one thing that i notice is that the RAM consumption is gone Down ( now Used: 4.6 Gbps to 5 Gbps). I also installed "Check_Point_SmartConsole_R80_10_jumbo_HF_B161_Win" and it is working nicely.

I will monitor the behavior and if there is any  change i will let you know. 

Thank you ALL for your support.

Regards,

Mauro de Sousa