Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
BunleangMeng_KH
Contributor
Jump to solution

Checkpoint 6600 interfaces

I got a new box of checkpoint security gateway, I have done factory reset

I tried to connect to the console port and login, but the interface was so strange that it didn't look like the normal interface of a security gateway. Could anyone tell me about the interface? 

 

normal security gateway that I use to configure the interface of gateway, it doesn't like below output, and how to remove the it to normal of interface security gateway?

 

[Expert@gw-bd36bc:0]# dmiparse System Product

QM-10-00

[Local SGM] gw-bd3310> show configuration interface
set interface Mgmt state on
set interface Mgmt auto-negotiation on
set interface Phys-Sync state off
set interface ethsBP1 state on
set interface ethsBP1-01 state on
set interface ethsBP1-02 state on
set interface ethsBP1-03 state on
set interface ethsBP1-04 state on
set interface ethsBP2 state on
set interface ethsBP3 state on
set interface ethsBP4 state on
set interface ethsBP5 state on
set interface ethsBP6 state on
set interface ethsBP7 state on
set interface ethsBP8 state on
set interface lo state on
set interface lo ipv4-address 127.0.0.1 mask-length 8
[Local SGM] gw-bd3310>

[Local SGM] gw-bd3310> show configuration

set message caption off
set core-dump enable
set core-dump total 1000
set core-dump per_process 2
set core-dump send_crash_data off
set chassis id 1 general snmp_retries 3
sh: chassis:id:1:general:snmp_retries: command not found
set chassis id 1 alert_threshold fans_threshold_high 11
set chassis id 1 alert_threshold fans_threshold_low 9
set chassis id 1 alert_threshold cpus_temperature_threshold_low 60
set chassis id 1 alert_threshold cpus_temperature_threshold_high 95
set chassis id 1 alert_threshold power_consumption_threshold_perc_low 80
set chassis id 1 alert_threshold power_consumption_threshold_perc_high 90
set chassis id 1 module CMM IP 198.51.100.33
set chassis id 1 module CMM snmp_auth MD5
set chassis id 1 module CMM status active
set chassis id 1 module CMM username asg1
set chassis id 1 module CMM secondary_ip 198.51.100.233
set chassis id 1 module SSM1 IP 198.51.100.32
set chassis id 1 module SSM1 ports_amount 40
set chassis id 1 module SSM1 snmp_auth MD5
set chassis id 1 module SSM1 status active
set chassis id 1 module SSM1 username asg1
set chassis id 1 module SSM1 legacy_vlan off
set chassis id 1 module SSM1 spi_affinity off
set chassis id 1 module SSM2 IP 198.51.100.232
set chassis id 1 module SSM2 ports_amount 40
set chassis id 1 module SSM2 snmp_auth MD5
set chassis id 1 module SSM2 status active
set chassis id 1 module SSM2 username asg1
set chassis id 1 module SSM2 legacy_vlan off
set chassis id 1 module SSM2 spi_affinity off
set chassis id 1 module Mgmt ports_amount 2
set chassis id 1 module Mgmt snmp_auth MD5
set chassis id 1 module Mgmt status active
set chassis id 1 module Mgmt username asg1
set chassis id 1 modules_amount fans 6
set chassis id 1 modules_amount ssm 2
set chassis id 1 modules_amount power_units 5
set chassis id 1 modules_amount cmm 2
set chassis id 2 general snmp_retries 3
sh: chassis:id:2:general:snmp_retries: command not found
set chassis id 2 alert_threshold fans_threshold_high 11
set chassis id 2 alert_threshold fans_threshold_low 9
set chassis id 2 alert_threshold cpus_temperature_threshold_low 60
set chassis id 2 alert_threshold cpus_temperature_threshold_high 95
set chassis id 2 alert_threshold power_consumption_threshold_perc_low 80
set chassis id 2 alert_threshold power_consumption_threshold_perc_high 90
set chassis id 2 module CMM IP 198.51.100.33
set chassis id 2 module CMM snmp_auth MD5
set chassis id 2 module CMM status active
set chassis id 2 module CMM username asg1
set chassis id 2 module CMM secondary_ip 198.51.100.233
set chassis id 2 module SSM1 IP 198.51.100.32
set chassis id 2 module SSM1 ports_amount 40
set chassis id 2 module SSM1 snmp_auth MD5
set chassis id 2 module SSM1 status active
set chassis id 2 module SSM1 username asg1
set chassis id 2 module SSM1 legacy_vla

 

set chassis high-availability port eth1-01 priority 1
set chassis high-availability port eth1-02 priority 1
set chassis high-availability port eth1-03 priority 1
set chassis high-availability port eth1-04 priority 1
set chassis high-availability port eth1-05 priority 1
set chassis high-availability port eth1-06 priority 1
set chassis high-availability port eth1-07 priority 1
set chassis high-availability port eth1-08 priority 1
set chassis high-availability port eth1-09 priority 1
set chassis high-availability port eth1-10 priority 1
set chassis high-availability port eth1-11 priority 1
set chassis high-availability port eth1-12 priority 1
set chassis high-availability port eth1-13 priority 1
set chassis high-availability port eth1-14 priority 1
set chassis high-availability port eth1-15 priority 1
set chassis high-availability port eth1-16 priority 1
set chassis high-availability port eth1-17 priority 1
set chassis high-availability port eth1-18 priority 1
set chassis high-availability port eth1-19 priority 1
set chassis high-availability port eth1-20 priority 1
set chassis high-availability port eth1-21 priority 1
set chassis high-availability port eth1-22 priority 1
set chassis high-availability port eth1-23 priority 1
set chassis high-availability port eth1-24 priority 1
set chassis high-availability port eth1-25 priority 1
set chassis high-availability port eth1-26 priority 1
set chassis high-availability port eth1-27 priority 1
set chassis high-availability port eth1-28 priority 1
set chassis high-availability port eth1-29 priority 1
set chassis high-availability port eth1-30 priority 1
set chassis high-availability port eth1-31 priority 1
set chassis high-availability port eth1-32 priority 1
set chassis high-availability port eth1-33 priority 1
set chassis high-availability port eth1-34 priority 1
set chassis high-availability port eth1-35 priority 1
set chassis high-availability port eth1-36 priority 1
set chassis high-availability port eth1-37 priority 1
set chassis high-availability port eth1-38 priority 1
set chassis high-availability port eth1-39 priority 1
set chassis high-availability port eth1-40 priority 1
set chassis high-availability port eth1-41 priority 1
set chassis high-availability port eth1-42 priority 1
set chassis high-availability port eth1-43 priority 1
set chassis high-availability port eth1-44 priority 1
set chassset chassis high-availability port eth2-02 priority 1

0 Kudos
1 Solution

Accepted Solutions
Chris_Atkinson
Employee Employee
Employee

The gateway has been installed with the Maestro / SP version ISO.

Please reimage it via USB if you intend on using it as a normal gateway.

CCSM R77/R80/ELITE

View solution in original post

5 Replies
Chris_Atkinson
Employee Employee
Employee

The gateway has been installed with the Maestro / SP version ISO.

Please reimage it via USB if you intend on using it as a normal gateway.

CCSM R77/R80/ELITE
BunleangMeng_KH
Contributor

Thank you for your feedback. 

yes, I need to use as a normal gateway.  I will boot a new image. 

0 Kudos
BunleangMeng_KH
Contributor

remage from Maestro / SP version ISO to normal gateway. the procedure is the same reimage gateway to gateway?

or different? can share the link how to perform?

0 Kudos
Chris_Atkinson
Employee Employee
Employee

Isomorphic utility will allow you to build a USB with the correct ISO.

You can obtain both from support center. USB 2.0 key is needed here.

https://support.checkpoint.com/results/sk/sk65205

 

CCSM R77/R80/ELITE
the_rock
Legend
Legend

Just use link Chris gave, thats all you need.

Best,

Andy

0 Kudos

Leaderboard

Epsum factorial non deposit quid pro quo hic escorol.

Upcoming Events

    CheckMates Events