cancel
Showing results for 
Search instead for 
Did you mean: 
Create a Post

SMB Backup firmware version from CLI

Jump to solution

Im Embedded GAiA WebGUI, i can see the factory firmware version under Devices > System > System Operations. But clish in # show diag only displays the active firmware version. But is there any possible clish command to show it ?

Tags (1)
0 Kudos
2 Solutions

Accepted Solutions

Re: SMB Backup firmware version from CLI

Jump to solution

Seems it is available - have a look at:

pfrm2.0/opt/fw1/bin/firmware_ver.sh

Usage: firmware_ver.sh [-d <url> <image> <chksum>|-r|-v]
        -d : Download from given URL to given path and verify checksum
        -r : Revert to saved image
        -v : Display firmware versions

Expert@seven-eleven]# firmware_ver.sh -v
77 20 80 990172370 /dev/mtd2    77 20 75 990172320 /dev/mtd4

View solution in original post

0 Kudos

Re: SMB Backup firmware version from CLI

Jump to solution

Since R77.20.85, the 'show diag' command shows the secondary and default image name/version in addition to the current one.

Current system info
-----------------------------------
Current image name: R77_990172715_20_85
Current image version: 715
Previous image name: R77_990172701_20_85
Previous image version: 701
Default image name: R77_990172392_20_80
Default image version: 392

View solution in original post

7 Replies

Re: SMB Backup firmware version from CLI

Jump to solution

I found it is not # show saved-image - that command does not work....

0 Kudos
Highlighted

Re: SMB Backup firmware version from CLI

Jump to solution

Of course, a simple ver gives the active Firmware Version...

0 Kudos

Re: SMB Backup firmware version from CLI

Jump to solution

Seems it is available - have a look at:

pfrm2.0/opt/fw1/bin/firmware_ver.sh

Usage: firmware_ver.sh [-d <url> <image> <chksum>|-r|-v]
        -d : Download from given URL to given path and verify checksum
        -r : Revert to saved image
        -v : Display firmware versions

Expert@seven-eleven]# firmware_ver.sh -v
77 20 80 990172370 /dev/mtd2    77 20 75 990172320 /dev/mtd4

View solution in original post

0 Kudos

Re: SMB Backup firmware version from CLI

Jump to solution

Since R77.20.85, the 'show diag' command shows the secondary and default image name/version in addition to the current one.

Current system info
-----------------------------------
Current image name: R77_990172715_20_85
Current image version: 715
Previous image name: R77_990172701_20_85
Previous image version: 701
Default image name: R77_990172392_20_80
Default image version: 392

View solution in original post

Hakim
Ivory

Re: SMB Backup firmware version from CLI

Jump to solution

Hi folks, 

I m a bit new in Check Point and i am looking for the CLI command to check the firmware for R77.30, 

I tried the command as you mention in your comment "# firmware_ver.sh -v" but doesn't work 

Ver (work as you can see below)

ver
Product version Check Point Gaia R77.30
OS build 5
OS kernel version 2.6.18-92cp
OS edition 32-bit

 

Thank's for your advices

0 Kudos
Admin
Admin

Re: SMB Backup firmware version from CLI

Jump to solution
This is from one of the Enterprise appliances that does NOT have "backup firmware."
When you boot the appliance, you can "factory reset" to a given software release, depending on what your appliance was initially imaged with.
0 Kudos

Re: SMB Backup firmware version from CLI

Jump to solution

On 14x0 appliances:

- Previous image: # firmTool -c /dev/mtd2

- Current image  : # firmTool -c /dev/mtd4

- Default image   : # firmTool -c /dev/mtd6