Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted

Unable to install R80.10 on VMware workstation

Hi all !

 

I want to try R810.10 on my computer in Vmware Workstation 12, but after installing Management Center I get this error in GUI Clients Section (User Management - GUI Clients):

 

Management Server cannot be reached. Check your management configuration and try again.

 

Also when  I try connect to installed Management center via SmartDashboard and also take error:

 

Unable to connect to server

 

What happening ? Why I can`t normal install CheckPoint ?

 

Early I successfully played with CheckPoint R77.30 (Management and Gateway).

 

Regards,

Vassili 

Tags (2)
16 Replies
Highlighted
Nickel

Depending on CPU/Memory it can take quite a while before you can login for the first time as the database is being built.  After install use "top" command to watch for CPU to die down to almost nothing and then try to login. 

0 Kudos
Highlighted
Copper

I cant even install Management in vm player.

it gives me error:
Cannot install Check Point Security Management Server. Please contact Check Point Technical Support.

Checking this sk110518 atm.

0 Kudos
Highlighted
Copper

Increasing the memory made the trick.

Highlighted

Hi all !

This is kind of magic ! It`s worked !

Install R80.10 management on Vmware Workstation 12.5 use this parameters:

Guest Operating System - Other Linux 2.6.x kernel 64-bit

Memory - 4GB

Processors - 2

Hard Disk (SCSI) - 90GB (Preallocated)

 

After complete web configuraton of Gaia portal need reboot, and hooray ! It`s worked !

  

Also trying install R80.10 on Oracle Virtual Box 5.1 with this parameters:

 

Guest Operating system - Linux 2.6 / 3.x / 4.x (64-bit)

Base Memory - 4096 MB

Processors - 2

Controller - SATA (87Gb)

 

And it`s alsow worked !

Thanks all for answers !

 

Regards,

Vassili

Highlighted
Admin
Admin

4GB of RAM doesn't meet the minimum requirements for R80.10 management.

6GB of RAM is considered the bare minimum, more is better.

Highlighted

Hello

Tried 6gb RAM and 8GB RAM too. But still am getting a white blank screen. It is staying like that no matter how long 

0 Kudos
Highlighted
Employee+
Employee+

Hi Ravindra

I want to help you.

Can you elaborate,

Where and when did you get the white screen , and what was the operation ?

Thanks

Dan

0 Kudos
Highlighted

Hello

Thanks. I found the problem. When I increased the number of cores I was able to access the GUI

0 Kudos
Highlighted

It works with 6GB, but in my experience it will be a big headache. If you have the RAM, go with 8GB. 

0 Kudos
Highlighted
Employee
Employee

Installed R80.10 management only running on VM workstation, 6GIG (8GIG suggested), 4 Core, using RHEL 5 - 64bit, 60GIG HDD (100GIG suggested).  Once you get the "LOGIN" prompt, another 3,4,5 minutes to get access to the WEBui is needed.  

Highlighted

I have tried the same specifications, but after I enter my login details I am getting a white blank screen. It is staying like that no matter how long i

0 Kudos
Highlighted
Employee
Employee

I guess the big question is: what is best. RHEL 5 or Other Linux 2.6.x kernel 64-bit. 

I've always used RHEL5, but have seen similar issues.

0 Kudos
Highlighted

Hello.

$FWDIR/conf/gui-clients file incorrect or no exist.

solution

1. ssh login

2. login export mode

3. change directory

    # cd $FWDIR/conf/

4. create gui-clients file and insert 'any'

    # vi gui-clients

    any  

5. try agin connect Management Server

thank you

Highlighted

List of gui-clients can be modified by cpconfig as well

and now to something completely different
0 Kudos
Highlighted

Thank you for your suggestions. I have the gui-clients file and still can't login.

Using the "cpconfig" command didn't help either. Please see below.

Any help would be much appreciated.

[Expert@HQ-MGR1:0]#
[Expert@HQ-MGR1:0]# cd $FWDIR/conf/
[Expert@HQ-MGR1:0]# pwd
/opt/CPsuite-R80/fw1/conf
[Expert@HQ-MGR1:0]#
[Expert@HQ-MGR1:0]# ls -l gui*
-rw-rw-r-- 1 admin config 4 Jul 19 13:51 gui-clients
[Expert@HQ-MGR1:0]#
[Expert@HQ-MGR1:0]# cat gui-clients
any
[Expert@HQ-MGR1:0]#
[Expert@HQ-MGR1:0]# exit
exit
HQ-MGR1>
HQ-MGR1>HQ-MGR1> cpconfig
This program will let you re-configure
your Check Point Security Management Server configuration.


Configuration Options:
----------------------
(1)  Licenses and contracts
(2)  Administrator
(3)  GUI Clients
(4)  SNMP Extension
(5)  Random Pool
(6)  Certificate Authority
(7)  Certificate's Fingerprint
(8)  Automatic start of Check Point Products

(9) Exit

Enter your choice (1-9) :3

Configuring GUI Clients...
==========================
GUI Clients are trusted hosts from which
Administrators are allowed to log on to this Security Management Server.
Failed to connect to database

Configuration Options:
----------------------
(1)  Licenses and contracts
(2)  Administrator
(3)  GUI Clients
(4)  SNMP Extension
(5)  Random Pool
(6)  Certificate Authority
(7)  Certificate's Fingerprint
(8)  Automatic start of Check Point Products

(9) Exit

Enter your choice (1-9) :9

Thank You...
HQ-MGR1>

0 Kudos
Highlighted
Employee+
Employee+

Hi , Your server is not communicating with the cpconfig client, check memory , free space , license.

If all tests have ended OK , run the cpm_doctor (read more in sk117219)