cancel
Showing results for 
Search instead for 
Did you mean: 
Create a Post

80.10 to 80.20 Pre-Upgrade Verifier

I'm attempting to run the 80.20 pre-upgrade verification script on my 80.10 management server, but nothing appears to be happening when I execute it.  I've run the tool in the past with no issues so I am assuming there is a problem with my syntax.   

I'm running ./pre_upgrade_verifier -p $FWDIR -c R80 -t R80.20 and am not getting an output.  The help doesn't list 80.10 as a possibility for the currently installed version so I'm partially wondering if its not supported.

where the Currently installed version is one of the following:
NGX_R65 (aliases: 6.0.1.0)
R70 (aliases: R70_R70, 6.0.1.6)
R71 (aliases: R71_R71, 6.0.1.7)
R75 (aliases: R75_R75, 6.0.2.0)
R75.20 (aliases: R75.20_R75.20, 6.0.2.1)
R75.40 (aliases: R75.40_R75.40, 6.0.2.5)
R75.40VS (aliases: R75.40VS_R75.40VS, 6.0.3.0)
R76 (aliases: R76_R76, 6.0.3.5)
R77 (aliases: R77_R77, 6.0.4.0)
R80 (aliases: R80_R80, 6.0.4.8)

The file permissions for the entire upgrade pack are below

-rw-r----- 1 admin root 19141755 Jan 22 10:00 Check_Point_R80.20_Gaia_SecurePlatform_Migration_Tools.tgz
-rwxr-xr-x 1 105 80 893915 Dec 6 03:52 gtar
-rwxr-xr-x 1 105 80 241318 Dec 6 03:52 gzip
-rwxr-xr-x 1 105 80 9210256 Dec 6 03:52 ips_upgrade_tool
-rwxr-xr-x 1 105 80 4636 Dec 6 03:52 mgmt_puv.sh
-rwxr-xr-x 1 105 80 14529536 Dec 6 03:52 migrate
-rw-r--r-- 1 105 80 70783 Dec 6 03:52 migrate.conf
-rw-r--r-- 1 105 80 107 Dec 6 03:52 plugin_pack.conf
-rwxr-xr-x 1 105 80 8388116 Dec 6 03:52 plugin_upgrade_matcher
-rwxr--r-- 1 105 80 19175 Dec 6 03:52 ppidb.conf
-rwxr-xr-x 1 105 80 20965372 Dec 6 03:52 pre_upgrade_verifier
-rwxr-xr-x 1 105 80 1468920 Dec 6 03:52 puv_report_generator

8 Replies

Re: 80.10 to 80.20 Pre-Upgrade Verifier

Try "echo $?" straight after executing the script in case you get a non-0 exit status code.

0 Kudos

Re: 80.10 to 80.20 Pre-Upgrade Verifier

Thanks Nicholas, is this correct (below is my output when i ran "echo $?" after running the script)?

#./pre_upgrade_verifier -p $FWDIR -c R80 -t R80.20
# echo $?
0

0 Kudos

Re: 80.10 to 80.20 Pre-Upgrade Verifier

Code 0 is translated to a clean exit without any problems or issues. It basically means that your script run successfully.

I will attempt to reproduce the problem at the earliest opportunity and let you know of my findings if they are any different.

0 Kudos

Re: 80.10 to 80.20 Pre-Upgrade Verifier

If you are already on r80.x then preverifiyng doesn’t make much sense..

0 Kudos
Highlighted

Re: 80.10 to 80.20 Pre-Upgrade Verifier

It pre-specifies R80 to R80.20 as one of the supported pre-verification paths and the pre-verifier has been helpful in the past at identifying issues in my environment

0 Kudos

Re: 80.10 to 80.20 Pre-Upgrade Verifier

Hello, 

 

Take a look on Migrate to R80.20 TechTalk

0 Kudos
abihsot__
Nickel

Re: 80.10 to 80.20 Pre-Upgrade Verifier

Hi Kevin,

 

were you able to find what was causing the issue?

0 Kudos
emmanuel
Ivory

Re: 80.10 to 80.20 Pre-Upgrade Verifier

Hi,

In case someone still thinks it's an issue, not it's not cos PUV is not supported for R80.10 upgrade to R80.20. And this is because it's not necessary. Just take your snapshot/backup and run upgrade with CPUSE.

See https://sc1.checkpoint.com/documents/R80.20_GA/WebAdminGuides/EN/CP_R80.20_Installation_and_Upgrade_...

 

HTH,

Emmanuel.

0 Kudos