Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
Mazin_D
Contributor
Jump to solution

R77.10 maintenance mode

Hi,

after rebooting the primary in XL cluster , I got the below message:

*** please reboot in the maintenance mode to repair filesystem 

when I rebooted the firewall , can't see "press any key to see boot menu " . I read it could be defaulted to 0 second.

is there is thing I can do ? any advice is highly appreciated .

0 Kudos
1 Solution

Accepted Solutions
Nick_Doropoulos
Advisor

Hi Mazin,

Try the following:

1) Log into the device and navigate to expert mode.

2) Edit the /boot/grub/menu.1st and change its timeout parameter from 0 to 4. Save the changes.

3) Reboot the machine.

4) Press a key on the "Press any key to see the boot menu" screen. This should open the Check Point Boot Menu.

5) Choose the "Start in maintenance mode".

6) Enter the Expert mode credentials.

7) Follow sk92442 to repair the filesystem.

 

I hope that helps.

View solution in original post

(1)
9 Replies
Nick_Doropoulos
Advisor

Hi Mazin,

Try the following:

1) Log into the device and navigate to expert mode.

2) Edit the /boot/grub/menu.1st and change its timeout parameter from 0 to 4. Save the changes.

3) Reboot the machine.

4) Press a key on the "Press any key to see the boot menu" screen. This should open the Check Point Boot Menu.

5) Choose the "Start in maintenance mode".

6) Enter the Expert mode credentials.

7) Follow sk92442 to repair the filesystem.

 

I hope that helps.

(1)
Mazin_D
Contributor

thanks for your reply Nick, but how can I login to the device and the boot is stuck there ?

0 Kudos
HeikoAnkenbrand
Champion Champion
Champion

Only FYI R77.10 is out of support. Therefore it is not possible to open a TAC ticket.

If it is still possible to log in please follow this link:

How to check the hard drive integrity in Gaia/SecurePlatform OS with the 'fsck' command.

If you can't login any more use this HDT:

Using the Check Point Appliance Hardware Diagnostic Tool

If the hard disk is still ok then install a backup or snapshot.

➜ CCSM Elite, CCME, CCTE
0 Kudos
_Val_
Admin
Admin

Looks like HDD failure to me

0 Kudos
Mazin_D
Contributor
unfortunately, I am not able to login as it keep presents me with the message to reboot in the maintenance mode to repair filesystem. the Hardware diagnostic tool is not supported in the IP Series appliances, ours is IP290.
0 Kudos
PhoneBoy
Admin
Admin
The fact this is an IP Appliance is an incredibly important detail that should have been mentioned upfront.
Is it running IPSO or Gaia?
A screenshot of exactly what you see would be helpful.
0 Kudos
Mazin_D
Contributor

Hi,

Its running Gaia, below the screenshot :-

fsck.PNG

0 Kudos
GenDeebongz
Explorer

Hi All

Was this ever resolved,

I have the exact same issue with my 80.10 gateway.

0 Kudos
Ks07
Explorer

1) Log into the device and navigate to expert mode.

2) Edit the /boot/grub/menu.1st and change its timeout parameter from 0 to 4. Save the changes.

3) Reboot the machine.

4) Press a key on the "Press any key to see the boot menu" screen. This should open the Check Point Boot Menu.

5) Choose the "Start in maintenance mode".

6) Enter the Expert mode credentials.

7) Follow sk92442 to repair the filesystem.

0 Kudos

Leaderboard

Epsum factorial non deposit quid pro quo hic escorol.

Upcoming Events

    CheckMates Events