cancel
Showing results for 
Search instead for 
Did you mean: 
Create a Post

Not Able To Find the Serial Number

Jump to solution

Hi Every One.

I have a  UTM-1 570 and i want to get the Serial no of the device.But i am not able to do that.

Please suggest the CLI command to get the serial no of the unit.

thanks in advance.

0 Kudos
1 Solution

Accepted Solutions
Admin
Admin

Re: Not able to find the serial no.

Jump to solution
First of all, it would help if you had posted this in the correct space (should be Enterprise Appliances).
Given this is a UTM-1 570, it's highly likely this is running SPLAT, which I don't believe had a command to show the serial number.
Also, I recall some older appliances didn't have serial numbers burned into EEPROM or similar.
0 Kudos
17 Replies
Vladimir
Pearl

Re: Not able to find the serial no.

Jump to solution

> show asset all

0 Kudos

Re: Not able to find the serial no.

Jump to solution

I tried this and it's not showing the Serial no of the Unit.

0 Kudos
Vladimir
Pearl

Re: Not able to find the serial no.

Jump to solution

Ok then, go to the "Expert" mode and execute:

dmiparse | grep ‘Serial Number’ 

0 Kudos

Re: Not able to find the serial no.

Jump to solution
i also tried this,but no luck.
dmiparse |grep 'Serial Number'
Serial Number:
Serial Number:
Serial Number:
this is the output
0 Kudos
Vladimir
Pearl

Re: Not able to find the serial no.

Jump to solution

how about running this from the "Expert" mode: 

system_info System Information

0 Kudos

Re: Not able to find the serial no.

Jump to solution
for this,the output is:-
UTM-1
Not supported for this system
0 Kudos
Vladimir
Pearl

Re: Not able to find the serial no.

Jump to solution

Then in clish>

show asset hardware

 

0 Kudos

Re: Not able to find the serial no.

Jump to solution
No, still no luck
0 Kudos
Vladimir
Pearl

Re: Not able to find the serial no.

Jump to solution

What OS are you running on that UTM unit?

0 Kudos
Admin
Admin

Re: Not able to find the serial no.

Jump to solution
First of all, it would help if you had posted this in the correct space (should be Enterprise Appliances).
Given this is a UTM-1 570, it's highly likely this is running SPLAT, which I don't believe had a command to show the serial number.
Also, I recall some older appliances didn't have serial numbers burned into EEPROM or similar.
0 Kudos

Re: Not able to find the serial no.

Jump to solution
thank you for the information.
0 Kudos

Re: Not able to find the serial no.

Jump to solution
we are running on GAIA 77.10
0 Kudos

Re: Not able to find the serial no.

Jump to solution
You could use 'cpstat os'
This should give version info and info about the hardware, including serial number.
If that fails lookup the mac address of the Mgmt interface and look this up in the usercenter, there the serial number should also be mentioned.
Regards, Maarten

Re: Not able to find the serial no.

Jump to solution
i got only"SVN Foundation Build Number:"
0 Kudos

Re: Not able to find the serial no.

Jump to solution
then again maybe pops up the question why would you need the serial number?
All equipment is registered by the Mgmt MAC address within Check Point, also the licenses.
Regards, Maarten
0 Kudos
Highlighted

Re: Not able to find the serial no.

Jump to solution
yaa! but we are collecting the details for asset management only.
0 Kudos

Re: Not able to find the serial no.

Jump to solution

UTM 570 went completely out of support on 1-Apr-2017 - so regarding asset management, all we could do is recycle them, but not look at the serial... But maybe you want to play the serial number in the lottery ? 😁

0 Kudos