Create a Post
cancel
Showing results for 
Search instead for 
Did you mean: 
Sergej_Gurenko
Collaborator
Jump to solution

LOM password reset on 5600 and 12400 appliances

Hello

 

Can you please suggest if there is an option for LOM password reset? I hound instructions for setting IP, how about resetting LOM Lights Out Management password? 

 

Regards,

Serg

 

References:

sk97849 - Configuring IP Address for LOM card on 21400 appliance through the System Console

sk94670 - Setting Lights Out Management (LOM) IP address from SecurePlatform OS on Power-1 appliance...

 

  1. At the system console port, load the IPMI drivers into Linux memory: 

    [Expert@HostName]# /etc/init.d/ipmi start 

    Should get:
    Starting ipmi drivers: [ OK ] 

    Note: It takes around 20 seconds to load the drivers. 

  2. Check if LOM LAN factory default settings are correct. The bold IP addresses indicated by "<----" are the ones that will be modified. 

    [Expert@HostName]# ipmitool lan print 1
    Set in Progress         : Set Complete
    Auth Type Support       : NONE MD2 MD5 OEM
    Auth Type Enable        : Callback : MD2 MD5 OEM
                            : User     : MD2 MD5 OEM
                            : Operator : MD2 MD5 OEM
                            : Admin    : MD2 MD5 OEM
                            : OEM      :
    IP Address Source       : Static Address
    IP Address              : 192.168.0.100    <----
    Subnet Mask             : 255.255.255.0    <----
    MAC Address             : XXXXXXXXXXXXXXX
    SNMP Community String   : AMI
    IP Header               : TTL=0x00 Flags=0x00 Precedence=0x00 TOS=0x00
    BMC ARP Control         : ARP Responses Disabled, Gratuitous ARP Disabled
    Gratituous ARP Intrvl   : 0.0 seconds
    Default Gateway IP      : 192.168.0.1     <-----
    Default Gateway MAC     : 00:00:00:00:00:00
    Backup Gateway IP       : 0.0.0.0
    Backup Gateway MAC      : 00:00:00:00:00:00
    RMCP+ Cipher Suites     : Cipher Suite Priv Max   : XXXXXXXXXXXXXXX
                            :     X=Cipher Suite Unused
                            :     c=CALLBACK
                            :     u=USER
                            :     o=OPERATOR
                            :     a=ADMIN
                            :     O=OEM
  3. Set the timeout value for the LOM console switch to 59 minutes: 
0 Kudos
1 Solution

Accepted Solutions
Wolfgang
Authority
Authority

sk120793 => ipmitool user set password 2 vpn123

Or

 sk127573  ipmitool raw 0x2e 0x02 ( Full reset of LOM)

 

View solution in original post

3 Replies
Wolfgang
Authority
Authority

sk120793 => ipmitool user set password 2 vpn123

Or

 sk127573  ipmitool raw 0x2e 0x02 ( Full reset of LOM)

 

maninderdeol
Explorer

Hi,

Just to add into it. If you perform a full reset on LOM on remote Firewall, it will make it inaccessible unless you have 192.168.X.X subnet to talk to it. However, the work around is do " ipmitool lan print 1" or " ipmitool lan print 8" and check the exisiting IP Address and Default Gateway details. Once you have the details, you can perform full reset using  "ipmitool raw 0x2e 0x02"  under the expertmode in CLI and then assign LOM same IP Address using "lomipset <LOM_IP_ADDRESS> <LOM_NETMASK> <LOM_DEFAULT_GW_ADDRESS>” command under the expertmode and access the LOM using a Web browser, login using defaul login details, and go through the setup process.

0 Kudos
HusMo
Explorer
Explorer

Hello Sergej

Old thread but I just came across this when trying to kick a couple of LOM cards into action. Symptom, LOM MACs not seen on switchport (hence LOMs unreachable).

I tried ipmitool raw 0x2e 0x02 but it didn't do anything. Found the command below on a Nutanix site, tried it and worked perfectly (once cards reset, MACs seen on switchports and LOMs reachable, with configuration retained):

# ipmitool mc reset cold

Maybe a good one to update sk127573 with before doing full factory reset

cheers

0 Kudos

Leaderboard

Epsum factorial non deposit quid pro quo hic escorol.

Upcoming Events

    CheckMates Events