topic Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)? in General Topics

4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 15:00:12 GMT

is my subject statement actually correct and validated?

my customer is having following message by Upgrade Wizard:

"No upgrade path available for this selection, for valid upgrade paths, click here" ...

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

mdjmcnally — Tue, 28 Jan 2020 15:17:43 GMT

Just ran the upgrade wizard

New Installation makes comment about 8Gb required but doesn't say incompatible.

What is the starting point

Even if start at SecurePlatform and Gaia R80.40 as endpoint then says need to do an R80.30 intermediate.

Maybe updated since your customer ran however certainly not seeing what you have had reported to you.

Would run it yourself and see what you get, certainly get the customer to run again but I certainly wouldn't say that your statement is correct based on what seeing.

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 15:20:51 GMT

Thanks! That's what I wanted to rule out as it seems that "Upgrade" isn't either recommended or possible - neverthenless I believe I do have customer who has 4800's in HA on R80.30 with 8GB of RAM so they are looking into the Upgrade path once JHF number 2 is released. Let's see what others says, I really wonder what's going on and also do not believe myself as I did the upgrade on eSXI VM with same parameters as appliance and it did work (tgz wrapper).

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

G_W_Albrecht — Tue, 28 Jan 2020 15:28:49 GMT

Release notes are quite clear:

Appliances:

GW with 4 GB RAM is supported, but Stand-Alone needs at least 8 GB.

SMS with 4 GB RAM is supported as SMS only, SMS and Log Server need 8 GB, SMS, Smart Event and Log Server need 16 GB.

Open Servers:

R80.40 for Open Servers is supported only for Security Management Servers and needs & GB RAM. GW and StandAlone for Open Servers will need a Jumbo HFA.

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 15:32:25 GMT

Thanks, I've seen that but couldn't believe that ALL-in-ONE req. 8GB.
Fine, fair enough. Point taken, I'll pass it over to the relevant people.

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 15:35:22 GMT

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 16:48:16 GMT

[Expert@cp4800:0]# cpprod_util CPPROD_GetValue CPupgrade-tools-R80.40 BuildNumber 1
994000242
[Expert@cp4800:0]# $MDS_FWDIR/scripts/migrate_server verify -skip_upgrade_tools_check -v R80.40
The verify operation finished successfully.
[Expert@cp4800:0]#

*** so is that device compatible/doable or not guys ?

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

mdjmcnally — Tue, 28 Jan 2020 16:48:32 GMT

So have they downloaded the Package and using the Verifier in CPUSE or simply running the upgrade wizard on the Check Point website.

If downloaded the package have they the latest Deployment Agent.

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 16:50:47 GMT

all YES.
shell shows as below so hope all will be good, however the Importing via WebUI CPUSE does not finish ... and hang on "Importing and installing the upgrade tools package ... ". very weired 😞

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 16:54:21 GMT

downloading Check_Point_R80.40_T294_Fresh_Install_and_Upgrade.tgz
and will try to import that onto their 4800's. 1st things 1st 🙂

ps. it is upgrade from up&running R80.30 recent take

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

mdjmcnally — Tue, 28 Jan 2020 16:54:48 GMT

So that is running the Management Migration Tool which simply checks that can export the policy, not what can import into

Not the same as running the Upgrade Wizard.

How exactly is the end user getting the error message?

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

Jerry — Tue, 28 Jan 2020 16:56:46 GMT

here, when trying to accomodate all appropiate options:

https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doShowupgradewizard

try and include 4800's as a source (gaia)

Re: 4800 Appliance not compatible with R80.40 (All-in-one installation)?

mdjmcnally — Tue, 28 Jan 2020 17:07:24 GMT

That is what presumed orgionally was running. With that then could when specifying Standalone and 4800 could even show as far back as SecurePlatform R75.47 to Gaia R80.40 and simply provided intermediate R80.30 was needed.

That tool shows no problems other then warning about 8Gb which they have already.