topic Re: Dynamic Mount Utility (DMU) in Endpoint

Dynamic Mount Utility (DMU)

PhoneBoy — Mon, 11 Sep 2017 15:58:59 GMT

The Dynamic Mount Utility is needed to mount drives that have been encrypted with Check Point's Full Disk Encryption product. This is needed if the operating system fails on the endpoint computer.

The Dynamic Mount Utility:

Lets you access hard disks connected through a USB port
Is hardware independent
- Note - The Full Disk Encryption Alternative Boot Menu is not hardware independent.
Runs from a Windows environment, or from a pre-prepared WinPE or BartPE CD/DVD.
Replaces the Full Disk Encryption slaving feature of previous releases.
Does not require Full Disk Encryption on the disk.

There are two versions of this tool:

1.x for R7x versions of Endpoint:
- Full Disk Encryption - Dynamic Mount Utility 1.6
- Dynamic Mount Utility 1.6 Administration Guide
2.x for E80.x versions of Endpoint:
- Full Disk Encryption - Dynamic Mount Utility 2.2
- Dynamic Mount Utility 2.0 Administration Guide

Re: Dynamic Mount Utility (DMU)

John_Briggs — Wed, 04 Oct 2017 19:51:26 GMT

Two extra points. When installing the DMU, do not install the software on a device in which the Check Point Endpoint Client is loaded. We use a separate device that does not have the endpoint client installed.

Second, although the entire drive doesn't need to be fully encrypted, the encrypted volume for which you are trying to recover data needs to be fully encrypted. If the device was in the middle of encryption and the device failed, you need to initiate recovery procedures to remove encryption from the device to gain access to that data.

Re: Dynamic Mount Utility (DMU)

Angelo_Laino — Thu, 15 Feb 2018 15:10:32 GMT

Hi,

I used the procedure described on Full Disk Encryption - Dynamic Mount Utility 1.6, I receive the message that the hd has been unprotected but clicking on the drive unlocked, pc go in hangs. I also tried to connect the hdd as slave and installed the Windows version of the DMU and still the same. I used psmain tool because the original error is generated by these but aftere the restore DB I get again the error. I also used the .rec process and after click on Recover All getting again the psmain error. I use an hdd diagnostic tool and no error has been found. Have you any suggestion?

Thank a lot!

Re: Dynamic Mount Utility (DMU)

PhoneBoy — Thu, 15 Feb 2018 17:35:48 GMT

It's probably worth a TAC case to troubleshoot.

Re: Dynamic Mount Utility (DMU)

Jerry2cp — Sat, 28 Sep 2024 06:46:01 GMT

Your provided links are not work, could you provide a valid way for download DMU tools?

Re: Dynamic Mount Utility (DMU)

_Val_ — Sun, 29 Sep 2024 10:45:05 GMT

Links are working just fine. You need to be logged into UserCenter before opening them.

Re: Dynamic Mount Utility (DMU)

Jerry2cp — Tue, 08 Oct 2024 07:08:02 GMT

do you mean support center or other special group? as I have logged into checkpoint, but not sure whether it is the right one, could you provide the link of the UserCenter? thanks

Re: Dynamic Mount Utility (DMU)

PhoneBoy — Tue, 08 Oct 2024 19:25:49 GMT

https://support.checkpoint.com
A 404 may be returned for these download links if you do NOT have an active Software Subscription associated with your ID.

Re: Dynamic Mount Utility (DMU)

mva — Wed, 09 Apr 2025 11:37:44 GMT

Hello mates!

Link in SK doesen't work. I have subscription (proved by downloading other software)

Re: Dynamic Mount Utility (DMU)

PhoneBoy — Wed, 09 Apr 2025 13:01:11 GMT

Not every download requires Software Subscription.
Please consult with Account Services to ensure you have the appropriate level of access.