topic Re: 5600 in VSX cluster not booting in Firewall and Security Management

5600 in VSX cluster not booting

Enyi_Ajoku — Mon, 27 Jan 2020 15:13:14 GMT

I've got two 5600 running VSX, at the moment the standby member doesnt complete it boot process. It give the following error below:

ACPI: Getting cpuindex for acpiid 0x5
ACPI: Getting cpuindex for acpiid 0x6
ACPI: Getting cpuindex for acpiid 0x7
ACPI: Getting cpuindex for acpiid 0x8
▒i8042.c: No controller found.
Reading all physical volumes. This may take a while...
Found volume group "vg_splat" using metadata type lvm2
12 logical volume(s) in volume group "vg_splat" now active
FATAL: Could not load /lib/modules/2.6.18-92cpx86_64/modules.dep: No such file or directory
Setting clock (utc): Mon Jan 27 09:42:13 EST 2020 [ OK ]
Starting udev: [ OK ]
Setting hostname: [ OK ]
DM multipath kernel driver not loadedooting in 3 seconds]
Setting up Logical Volume Management: 12 logical volume(s) in volume group "vg_splat" now active
[ OK ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/mapper/vg_splat-lv_current
/dev/mapper/vg_splat-lv_current contains a file system with errors, check forced.
/dev/mapper/vg_splat-lv_current: Unattached inode 1263413
Press any key to see the boot menu [Booting in 2 seconds]

/dev/mapper/vg_splat-lv_current: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
(i.e., without -a or -p options)
[FAILED]

*** An error occurred during the file system check.
*** Please boot in the maintenance mode to repair the filesystem

Appreciate all the help i can get

Thanks

Re: 5600 in VSX cluster not booting

G_W_Albrecht — Mon, 27 Jan 2020 15:44:19 GMT

Reboot, enter GAiA Boot Menu and select Maintenance Mode...

Re: 5600 in VSX cluster not booting

Wolfgang — Mon, 27 Jan 2020 17:24:48 GMT

How to check the hard drive integrity in Gaia/SecurePlatform OS with the 'fsck' command

to do a filesystem check in maintenance mode. Error messages are showing a problem with the filesystem.

Wolfgang

Re: 5600 in VSX cluster not booting

Enyi_Ajoku — Mon, 27 Jan 2020 18:12:11 GMT

Thank You,

I followed the instructions on the sk. At the moment i can log in to the gateway from clish which i couldn't but i am getting this error on the clish

CPPRODIS_init_error_logging: failed to retrieve directory path for product 'cpshared'. Cannot set cyclic log file for product 'cpshared' application 'cprid'.

Re: 5600 in VSX cluster not booting

mdjmcnally — Mon, 27 Jan 2020 18:31:21 GMT

Sounds like the basic installation now gone to the point where going to be easier to rebuild the box and re-establish the VSX on the box.

Re: 5600 in VSX cluster not booting

Maarten_Sjouw — Mon, 27 Jan 2020 18:41:11 GMT

Indeed, just put a USB stick with the right OS in it and do a clean install.
You probably had a power failure?
That can cause a corrupted disk.

Re: 5600 in VSX cluster not booting

Enyi_Ajoku — Mon, 27 Jan 2020 20:10:27 GMT

Here's another dilemma, i just observed that the SYNC, MGMT and Ethernet Ports link status are all down. Even though they are connected to Switch and Gateway (for SYNC)

I tried to connect my laptop to the Mgmt and SYNC interface and it didn't not light up. On the other hand, my 10Gb fiber ports that are connected to the same switch are up.

Bear in mind all of these where working till the posted issue happened.

Re: 5600 in VSX cluster not booting

Maarten_Sjouw — Mon, 27 Jan 2020 22:26:17 GMT

Again, do a clean install, nobody knows what is wrong with the box when these things happen, the only good solution is a clean install.