topic Re: Install R81.20 on TE250X in Firewall and Security Management

Install R81.20 on TE250X

EVSolovyev — Tue, 05 Nov 2024 16:38:29 GMT

Hi all.

I received a TE250X and some FWs. I looked at the installed software - it was very old (on the sandbox - "This is Check Point's software version R81 - Build 959"). I decided to do a reinstall. I took the current software - “Check Point R81.20 Gaia Fresh Install Take 634 (ISO)” and a fresh “ISOmorphic Tool version 1.1.0 build 207 (sk65205)”.

FW flashed without problems.

With sandbax I had a problem. When selecting “2 - Check Point appliance (any model)”, I get error:

Setup has detected the following appliance model: ¦
¦ TT-25-00. ¦
¦ ¦
¦ This model is not supported by this version. ¦
¦ Please contact Check Point support. ¦
¦ ¦
¦ Click Cancel to abort, or Ok to install as open server.

I checked that according to sk65205, the “BIOS” profile was selected in ISOmorphic.

Please tell me what I am doing wrong.

Re: Install R81.20 on TE250X

Lesley — Tue, 05 Nov 2024 21:32:41 GMT

This one you did right?

https://support.checkpoint.com/results/sk/sk65205#Installing%20Gaia%20/%20SecurePlatform%20OS%20on%20the%20Appliance%20/%20Open%20Server%20using%20the%20USB%20device

smart1 - only for installing on Smart-1 appliance and Threat Emulation appliances TE100X / TE250X / TE1000X / TE2000X

Re: Install R81.20 on TE250X

emmap — Wed, 06 Nov 2024 05:01:50 GMT

Please double check, is it TE250X or TE250XN? I think TT-25 may be the XN model, which only supports R81.

See: https://support.checkpoint.com/results/sk/sk173494

Looks like they are supported with R82 though, according to R82 release notes.

Re: Install R81.20 on TE250X

EVSolovyev — Thu, 07 Nov 2024 12:14:46 GMT

Hello.

Yes, my mistake - I have a TE250XN appliance.
The R82 software installed without any problem:

Image:jaguar_opt_main;777 Version:4.18.0-372.9.1cpx86_64

gw-9kdjef> cpinfo -y all

This is Check Point CPinfo Build 914000250 for GAIA

....

FW1 build number:

This is Check Point's software version R82 - Build 151

gw-9kdjef> show asset system
Platform: TT-25-00
Model: Check Point TE250XN
CPU Model: Intel(R) Xeon(R) Silver 4216 CPU
CPU Frequency: 2100.000 Mhz
Number of Cores: 32
CPU Hyperthreading: Enabled

gw-9kdjef>

But at the moment R82 is not recommended, so I have R81.20 on my SMC.

I took a special soft R81 for TE250XN - it doesn't fit, it asks to select a disk for installation:

+-----------------+ No driver found +------------------+
| |
| Unable to find any devices of the type |
| needed for this installation type. |
| Would you like to manually select your |
| driver or use a driver disk? |
| |
| +---------------+ +-------------------+ +------+ |
| | Select driver | | Use a driver disk | | Back | |
| +---------------+ +-------------------+ +------+ |
| |
| |
+------------------------------------------------------+

And this selection:

Re: Install R81.20 on TE250X

EVSolovyev — Thu, 07 Nov 2024 13:41:00 GMT

Think, may be this helps me. But not (try 5 flash drives). Every time I see:

Re: Install R81.20 on TE250X

EVSolovyev — Thu, 07 Nov 2024 14:21:36 GMT

The problem is solved, the issue is closed. Thanks to all who responded here, as well as to my colleague Alex O.

There are many places where it has been said that you should use USB 2.0, for example here.

My solution:

1. stay strong (I tried 7 flash drives with R82 installing normally - I think it's some problem of old kernel in R81).
2. TE250XN requires a special R81.
3. use a Transcend USB 3.0 8GB JF780 flash drive.

Or wait for R82 release and use it, at least it installs normally.

gw-9kdjef> cpinfo -y all

This is Check Point CPinfo Build 914000193 for GAIA

[IDA]

No hotfixes..

[MGMT]

No hotfixes..

[CPFC]

No hotfixes..

[FW1]

No hotfixes..

FW1 build number:

This is Check Point's software version R81 - Build 959