topic Re: Cluster shutdown and power on (remotely) in Firewall and Security Management

Cluster shutdown and power on (remotely)

civoulkidis — Fri, 15 Oct 2021 09:22:28 GMT

Hi,

In my company I have a cluster (2 Gateways). I know that we are going to have a scheduled power outage for some hours on the next weekend.

I would like to soft shutdown the appliances in order to avoid issues.

When the power recovers, are they going to power on automatically?

Is there any way to power on remotely the appliances?

Re: Cluster shutdown and power on (remotely)

_Val_ — Fri, 15 Oct 2021 09:53:59 GMT

You can certainly shutdown Gaia GWs by using "halt" command. However, you can only you can only remotely power-up those devices, if you have LOM card installed. Without LOM, I am afraid someone should still press the power on button after shutdown.

Sharing with us the model and SW version would help to give you more accurate advise.

Re: Cluster shutdown and power on (remotely)

civoulkidis — Fri, 15 Oct 2021 10:19:46 GMT

Platform: Check Point 6200P
Kernel: 3.10.0-693cpx86_64

Re: Cluster shutdown and power on (remotely)

_Val_ — Fri, 15 Oct 2021 11:30:28 GMT

How much RAM?

"mem" command on the appliance

Re: Cluster shutdown and power on (remotely)

civoulkidis — Fri, 15 Oct 2021 12:02:14 GMT

Total Virtual Memory 47857.70 MB
Active Virtual Memory 5389.63 MB
Total Real Memory 15798.30 MB
Active Real Memory 5389.49 MB
Free Real Memory 10408.81 MB

Re: Cluster shutdown and power on (remotely)

_Val_ — Fri, 15 Oct 2021 12:14:34 GMT

Okay, so it according to the datasheet, it should have LOM card installed.

If you never used it, look for LOM manual on the product page. The LOM card needs to be configured for proper use. Mind, you will have to have out of band access to LOM to power your GW off or on. Make sure the required network connectivity exists and is properly tested.

Re: Cluster shutdown and power on (remotely)

civoulkidis — Fri, 15 Oct 2021 12:26:13 GMT

Thank you very much for the details.

I suppose that I will need VPN access in order to be able to power on the Gateways.

The problem is that the VPN access runs through this cluster.

I am thinking to power off (soft) the one (A) of the devices just to be safe and sure that the one of my devices will not have issues from the power outage. The other device (B) will stay online until the power outage and will become "up" when the power recovers. If (B) is up with no issues, then I will have access to LOM in order to power on device (A).

Re: Cluster shutdown and power on (remotely)

Danny — Fri, 15 Oct 2021 12:29:21 GMT

fw> show lom ip-address - Show LOM IP address version - Show LOM firmware version fw> show lom version Firmware Revision : x.xx fw> show lom ip-address IP Address : x.x.x.x fw> set lom ip-address

Re: Cluster shutdown and power on (remotely)

genisis__ — Fri, 15 Oct 2021 12:30:40 GMT

show asset all would also indicate if LOM is installed.

Re: Cluster shutdown and power on (remotely)

Danny — Fri, 15 Oct 2021 12:34:06 GMT

Yep. I even created a SmartConsole Extension: LOM Info

Re: Cluster shutdown and power on (remotely)

_Val_ — Fri, 15 Oct 2021 14:01:46 GMT

FWs will not come up unattended. Someone needs to press the power button.

Re: Cluster shutdown and power on (remotely)

civoulkidis — Fri, 15 Oct 2021 15:29:38 GMT

Even if we have LOM configured?

Re: Cluster shutdown and power on (remotely)

_Val_ — Fri, 15 Oct 2021 15:52:17 GMT

If LOM is active, and the power is up, you can use it. However, without either access to LOM or pushing a physical button, an appliance will not power on.